Jump to content
SAU Community

Recommended Posts

This article lists it as street legal in Australia: http://www.ozzytyres.com.au/blog/the-nitto-nt-performance-and-invo-tyre-range/

Also Toyo refers to the R888 as street legal on their site, it's the same compound as NT01 (though different tread pattern): http://toyotires.com.au/tyres/motorsport-tyres/item/20-proxes-r888

Neither is really a street tyre though, my R888R's are super noisy at freeway speeds and wear a lot faster than my KU36's. Also they pick up a lot of debris from the street because of the soft compound, so I certainly wouldn't run them as the primary tyre on a street or mixed use car.

Link to comment
https://www.sau.com.au/forums/topic/468607-nitto-nt01/#findComment-7804564
Share on other sites

3 minutes ago, Subi001 said:

I ment I don't want to have 2 sets of wheels.

It will be cheaper to have 2 sets of wheels if you plan to do a lot of track time.

I had a set of Bridgestone semis which were great on the track but not good on the road so I sold them.. I got a second set of wheels at relatively low cost and got second hand slicks from the NZV8 series - they get rid of them when they drop off half a second per lap but are fine for track days. If you have quality track tyres then you will just waste them driving on the street (plus they will be marginal after a few km and in the wet).

If you are determined to have one set only then you have to favour street use and put up with less than optimum track times.

Link to comment
https://www.sau.com.au/forums/topic/468607-nitto-nt01/#findComment-7804650
Share on other sites

Want my car to be street driven and for track too. Want to spend money once on the tyres

It you really want to run a single set only get AD08R or similar. Not as hardcore as the NT01 but also unlike them actually good for both street and track.

Otherwise a dedicated second set of rims and tyres or the track would be a good call.
Link to comment
https://www.sau.com.au/forums/topic/468607-nitto-nt01/#findComment-7804662
Share on other sites

if you're serious about doing any track time then another set of rims/wheels will be needed. Great for track ain't great for street. Or as above, AD08R, but won't last long on street so cheaper to hav a 2nd set, in the long run.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/468607-nitto-nt01/#findComment-7804675
Share on other sites

I run 315/30/18 nt01's on my rear and 265/35/18 advan ad08r's on my front and it's a winning combo for street and track and also has been suprisingly grippy and drivable in the wet... But yes the rears do pickup a lot of small rocks etc. but for the level of grip I'm now getting it doesn't bother me.

IMG_1484440065.535818.jpg.4d218c68452254
Link to comment
https://www.sau.com.au/forums/topic/468607-nitto-nt01/#findComment-7804786
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...