Jump to content
SAU Community

GCG RB25DET GTX Highflow

Guilt-Toy
 Share

Recommended Posts

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

GCG RB25DET GTX Highflow

I got a highflow turbo,  its a 21u R33 turbo that has had a $1799 highflow job done by GCG in Sydney

They used a gtx30 compressor wheel,  this turbo is in good condition with very little shaft play.

Comes with dump pipe and actuator and return hose and oxy sensor - what you see in the pics is what you get.

The turbo is basically a gtx3071r

Newcastle NSW,  but can post no dramas,  cash on pickup or DD only please.

IMG_0202.thumb.JPG.10e4b894dc24a6440f1423bc8d57ef23.JPG

IMG_0200.JPG

IMG_0201.JPG

tag.jpg

Link to comment
https://www.sau.com.au/forums/topic/470173-gcg-rb25det-gtx-highflow/
Share on other sites
Guilt-Toy Grand Master

Guilt-Toy

Posted
  • Author
Posted

Will sell for $800 

No surge issues,  it was on my friends car and he wrote it off,  I sold my old r33 before i was able to fit it and its just been sitting there.

can post

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...