Jump to content
SAU Community

Recommended Posts

I would get a good quality radiator first. My GTR used to get hot around Hidden Valley after 3 laps. Fair enough I was giving it a foot full but for cheap motor insurance a good rad would be the go.

Ken

Dude get an oil cooler asap. The oil out of the turbo's and back into the block are the reason for the high oil and water temps. An oil cooler will bring both temps down. The oil temp will stay below 100 even if you fang at 160 all day.

Dude get an oil cooler asap.  The oil out of the turbo's and back into the block are the reason for the high oil and water temps.  An oil cooler will bring both temps down.  The oil temp will stay below 100 even if you fang at 160 all day.

Mmmm, had an oil cooler on my GTR and still had high temps, got a good rad and it fixed it. Oil temp to stay below 100 if you are doing 160 all day..... not up here mate.

RBNT

What kind of oil cooler did you have?

What brand/ size is your improved radiator?

Thanks for the heads up, would have thought the oil temps were causing most of the high heat since the oil usually climbs much higher on my GTR around the track than the water temp ever does.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...