Jump to content
SAU Community

What injector sleeves & o rings do I use for the PNT PERFORMANCE JUN STYLE PLENUM and standard injectors for Rb25det neo

adam wicks

By adam wicks,
in Engines & Forced Induction

 Share

Recommended Posts

  • 2 weeks later...
Sub Boy32 Rising Star

Sub Boy32

Posted
Posted

Have you measured the injector boss hole size? I'm not familiar with the Jun plenum but if it's made for the RB25 Neo it should be a standard 14/15mm seal. If it is made for a series one or series two RB25 they came out with a much larger sized seal for the side feed injectors. There are fuel rail kits from various brands (Race Works for eg) that come with adaptor collars to convert the manifold from side feed to top feed setup, just make sure you get one with the correct top seal size (can be 11m or 14mm normally)

 

  • Like 1
adam wicks Collaborator

adam wicks

Posted
  • Author
Posted
Have you measured the injector boss hole size? I'm not familiar with the Jun plenum but if it's made for the RB25 Neo it should be a standard 14/15mm seal. If it is made for a series one or series two RB25 they came out with a much larger sized seal for the side feed injectors. There are fuel rail kits from various brands (Race Works for eg) that come with adaptor collars to convert the manifold from side feed to top feed setup, just make sure you get one with the correct top seal size (can be 11m or 14mm normally)
 


Okay thanks
adam wicks Collaborator

adam wicks

Posted
  • Author
Posted

Okay so I just finished installing the plenum in my 34 it's running mint not missing a beat but it has the check engine, traction control off and slip error codes on the dash but it runs and drives fine do they just need to be cleared with the next tune ? Is it a tuner thing it is my car having issues ??

GTSBoy Grand Master

GTSBoy

Posted
Posted

Ah.  It's an R34.  OK, so you have a traction control CU somewhere in the car that is not happy that you have removed the TCS throttle and TCS throttle position sensor.  I was thinking that the codes were coming from the ECU, but if you have a PFC then that will give no f**k.  But the TCS CU will.  You can't have TCS if you remove the throttle for it, so you might as well find the TCS CU and pull it out.

I suggested Nistune because when you transplant a Neo into an older car with the TCS CU and so on in the car, the ECU chucks a wobbly and puts the code up.  Nistune allows you to mask those codes.  But in your case, it's the other way around.

  • Like 1
adam wicks Collaborator

adam wicks

Posted
  • Author
Posted
Ah.  It's an R34.  OK, so you have a traction control CU somewhere in the car that is not happy that you have removed the TCS throttle and TCS throttle position sensor.  I was thinking that the codes were coming from the ECU, but if you have a PFC then that will give no f**k.  But the TCS CU will.  You can't have TCS if you remove the throttle for it, so you might as well find the TCS CU and pull it out.

I suggested Nistune because when you transplant a Neo into an older car with the TCS CU and so on in the car, the ECU chucks a wobbly and puts the code up.  Nistune allows you to mask those codes.  But in your case, it's the other way around.

 

 

Okay thanks for the help you wouldn't know where the tcs cu is in an r34 gtt? I'll have a google also

 

adam wicks Collaborator

adam wicks

Posted
  • Author
Posted
Nope.  Google will be your friend.  I've never cared where it is in cars other than mine and thankfully, mine never had one!


Okay no worries I've tried googling it but couldn't find anything
Leroy Peterson Grand Master

Leroy Peterson

Posted
Posted
 Can't with a changed throttle body. 

 

Remove globes

Or.

Install original throttle body

Or.

Stare at always-on globe

 

Those are the options.

 

 

 

 

 

 

 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      First time we have seen lights 
    • Wazmond
      WGNC34 - floor mats

      By Wazmond · Posted

      I think Fitmit had some, have a look on there (theyre Australian as well)
    • soviet_merlin
      Howdy Y'all

      By soviet_merlin · Posted

      Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...