Jump to content
SAU Community

Recommended Posts

No oil pressure after car sits for a long time

So I have a RB25 neo engine that sat and didn't run for years. First time I tried to turn it over I could not get the oil pressure light to turn off after cranking it for along time repeatedly with the crank angle sensor unplugged. The oil pressure switch turned out to be working fine after putting an oil pressure gauge on it while trying to crank the engine and there was absolutely zero oil pressure.  Managed to get a hold of an accumsump and push oil through the engine which ended up solving the problem.The engine now has pressure, took the accusump off cranks and runs fine with oil pressure.

Ran and drove the car for a few weeks no problems than it sat again for a few months and now back to no oil pressure while cranking the engine with the cas off.

Has anyone heard of this problem before? Seems like there has to be some leak between the pump the pick up. I also have quite alot of oil pressure on idle from what I could remember 80 - 90 psi.

Or there's dirty lumps of sludge in there that you moved when you pressurised it with the Accusump and they have found their way back to cause you a problem.  Could be the inlet of the oil pump, or more a major gallery in the outlet area.

Probably worth doing a drop and refill with diesel, pressurise with diesel with the Accusump type of exercise to see if you can clean it out.

It could be something as silly as a lump of silicone/sealant hanging out of a flanged joint into the flow.  Like where the pickup bolts on.  Given that you seem to have silly high oil pressure at idle, you may have some sort of aftermarket pump/gears in there, which implies the opportunity for someone to have made a mess with sealant.

It has a nitto pump. I didnt have access to an accusump this time so I just gravity fed with a big funnel oil through the turbo oil feed and it managed to do the trick and the oil light turned off after cranking it over pretty quickly. Sounds like the oil pump is draining completely dry maybe?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...