Jump to content
SAU Community

Recommended Posts

If your M35 is overheating, check that the fan clutch is still supplying enough drive to move a decent amount of air. Fortunately, the fan clutch on the M35 is bolted together, which means it can be refilled. It will spin quite fast even it if it is completely stuffed. Search youtube for videos on how to check it (eg

1. Drive the car until everything is fully up to temperature. This will take a lot longer than to bring the temperature gauge up to its normal position.

2. Use an old magazine (or whatever) to slowly press against the spinning fan blades to slow them down. The fan will have a fair bit of momentum, even if the clutch is stuffed. I could hold the fan still with barely any pressure using my pinkie finger after it had slowed down. Again - watch some videos first.

If you confirm that the clutch is stuffed, you will need fluid to re-fill it. Many use Toyota fluid, example part numbers are 08816-03001 or 08816-06001 or 08816-10001, which are 3000, 6000 and 10000 CST respectively. Higher CST is thicker/more viscous. The Toyota fluid is about $17 for 12ml on ebay. The fluid is reported to be silicon oil, which cost me $20 for 50ml from a hobby store. You need about 80ml. I originally used 10000 cst from both Toyota and hobby store and they appeared the same. I don't know what viscosity is correct, but the car sounds like an old skool v8 with fan noise now, so its either correct or too viscous (or i added too much fluid).

EDIT: 10000 is definitely too thick - I have swapped it for 6000 which is better, but i'm still getting some belt squeal at high RPM, so either i have a belt/tension issue or its still too thick. Suggest 3000 as a starting point for anyone trying this.

Steps are;

1. Remove the air box snorkel, and air box.

2. Undo the 4 x 10mm headed nuts from the fan mount, and the 2 bolts holding the top of the fan shroud on, and lift them out together. This will require a bit of wriggling

3. Spray the bolts, screws and pin in the middle of the bi-metallic strip of the fan assembly with WD40, and leave to soak.

4. Take the fan off the fan clutch (10mm headed bolts)

5. Undo the phillips head screws holding the two halves of the clutch together, and pry them apart.

6. Leave the two halves upside down to drain the old fluid overnight, or clean them out with solvent. When i drained out the new 10000cst it didn't come out clean, so i'd recommend cleaning it out now, even though i didnt. AFAIK, WD40, Kerosine, Degreaser etc leave a greasy residue and will contaminate the new fluid, so brake cleaner is probably a better option.

7. Use needle nose pliers to verify that the pin at the center of the bi-metallic strip on the outside of clutch can turn a little / is not seized.

8. Fill the reservoir up with new fluid. I filled to the top of the first step, so about the level of the black rectangle in the centre.

large.hydraulic-clutch-1.png.0f9f6b0be29

9. Bolt the two halves together and re-attach the fan

10. Re-install the fan and shroud, being careful to get the tabs at the bottom of the shroud keyed in before you bolt the top on.

11. Beers

Link to comment
https://www.sau.com.au/forums/topic/473606-m35-refill-hydraulic-fan-clutch/
Share on other sites

4 hours ago, MrStabby said:

If your M35 is overheating, check that the fan clutch is still supplying enough drive to move a decent amount of air. Fortunately, the fan clutch on the M35 is bolted together, which means it can be refilled. It will spin quite fast even it if it is completely stuffed. Search youtube for videos on how to check it (eg

1. Drive the car until everything is fully up to temperature. This will take a lot longer than to bring the temperature gauge up to its normal position.)

2. Use an old magazine (or whatever) to slowly press against the spinning fan blades to slow them down. The fan will have a fair bit of momentum, even if the clutch is stuffed. I could hold the fan still with barely any pressure using my pinkie finger after it had slowed down. Again - watch some videos first.

If you confirm that the clutch is stuffed, you will need fluid to re-fill it. Many use Toyota fluid, example part numbers are 08816-03001 or 08816-06001 or 08816-10001, which are 3000, 6000 and 10000 CST respectively. Higher CST is thicker/more viscous. The Toyota fluid is about $17 for 12ml on ebay. The fluid is reported to be silicon oil, which cost me $20 for 50ml from a hobby store. You need about 85ml. I used 10000 cst from both Toyota and hobby store and they appeared the same. I don't know what viscosity is correct, but the car sounds like an old skool v8 with fan noise now, so its either correct or too viscous (or i added too much fluid).

Steps are;

1. Remove the air box snorkel, and air box.

2. Undo the 4 x 10mm nuts from the fan, and the 2 bolts holding the top of the fan shroud on, and lift them out together. This will require a bit of wriggling

3. Spray the bolts, screws and pin in the middle of the bi-metallic strip, and leave to soak.

4. Take the fan off the fan clutch (10mm bolts)

5. Undo the phillips head screws holding the two halves of the clutch together, and pry them apart.

6. Leave the two halves upside down to drain the old fluid overnight, or clean them out with solvent.

7. Use needle nose pliers to verify that the pin at the center of the bi-metallic strip on the outside of clutch can turn a little / is not seized.

8. Fill the reservoir up with new fluid. I filled to the top of the second step, so about the level of the top of the screw heads. This may be more than is required.

large.hydraulic-clutch-1.png.0f9f6b0be29

9. Bolt the two halves together and re-attach the fan

10. Re-install the fan and shroud, being careful to get the tabs at the bottom of the shroud keyed in before you bolt the top on.

11. Beers

Wow great effort, thank you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...