Jump to content
SAU Community

Rb25det Neo not revving past 5k?

lench

By lench,
in Engines & Forced Induction

 Share

Recommended Posts

lench Contributor

lench

Posted
Posted

Before anyone asks, yes i've done the usual searches but I couldnt find anything definitive :10_wink:
 

Background: Stock Rb25det NEO. standard intake, exhaust, boost and ecu.
Engine shuddering or hitting fuel cut whenever WOT and high boost (bucking like a mechanical bull), other than that, it ran fine. boosted down low ok, seems to run smooth(ish). didnt run rich, was getting on average about 450k's per tank
Replaced spark plugs with NGK coppers (1.1mm). Car then had absolutely no torque down low, would backfire constantly when cold or after WOT (which was necessary to get the friggin thing to move) and wouldn't rev over 5000rpm. It felt like it hit Rich and Retard. No codes were thrown

I noticed that the boost gauge was reading a little high after the plug change, and found a vacuum line from the charcoal canister had frayed and cracked causing a vacuum leak. Replaced this and boost reading went back to normal.

I then replaced the Airflow sensor (2nd hand from wreckers), Coilpacks (splitfires), Coilpack lead (Genuine) and Sparkplugs (NGK BKR6EIX-11).
This made a HUGE difference. the old coilpacks were likely from the factory and were just producing a weak spark.
Reset the ECU, still ran rich when cold (but not as rich), low-down torque came back but still cant rev over 5000rpm (feels like the engine just goes back to the R&R state)
It does backfire a little when cold or after WOT (more like a few pops instead of a full blown backfire). Still no codes thrown

Does the ECU lock out the top 2000 RPM when its 'learning'? or is it something else?

What should I be looking at next?
O2 Sensor?
Replace/check all Vacuum and Intake lines?
Cam angle sensor?

Really running out of ideas here

Link to comment
https://www.sau.com.au/forums/topic/473845-rb25det-neo-not-revving-past-5k/
Share on other sites
  • 3 months later...
lench Contributor

lench

Posted
  • Author
Posted (edited)

So this saga is still going on.
Taken it to two separate mechanics, both said that it 'seems' fine.. (despite the fact it cant even get close to the rev limiter in 2nd) 

Ran a boost leak test using my puny ryobi tyre inflator, it held 5psi for about 20 seconds which appears to be ok.. it seems that there's something else going on.
I've plugged in the consult cable and engine temps appear normal as far as i can tell.

Also appears that i'm running .75 bar of boost now (up from .5).
I changed the vac lines to and from the turbo and solenoid hoping that it was just a leaking line that was throwing everything off, still no joy (hiss/whistle noise cant be located with soap and water on any of the couplers)

I'm starting to think now, no power past a certain rev range + hiss/whistle noise + higher boost..  could it be an exhaust leak? or am i just reading too much into this?

Edited by lench
  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...