Jump to content
SAU Community

Recommended Posts

Last night I started having a problem with my car, a 1992 R32 GTR. The car has HKS GT2530s and standard camshafts and comes on to hard boost around 4000rpm.

When the car is coming onto hard boost at 4000rpm the car just "dies" and looses all power and the power fc warning light in the dash comes on and stays on solid. I know if it flashes in 3 increments at 0.5 second intervals it means detonation, and if the intervals are longer its the injectors maxing out, but this is just staying on solid and the injectors are nowhere near maximum (Sard 700cc) and the knock level is 1. The car is also still getting fuel as it comes flooding out the back of the exhaust (occasionally in a pretty orange/white burnt form), but I just cant figure it out. Spark plugs seem ok and are gapped at 0.8mm. It also has Z32 AFM's which were cleaned about 2 months ago. The car is running 1.2kg/cm2 boost.

When the car dies it sort of just splutters but doesnt sound like its misfiring.

Any ideas on what the problem could be?

Thanks.

Yeah the rev limiter is set to 8250rpm (factory rev limit). I forgot to mention this setup has been working faultlessly for the past few months, nothing was changed on the PowerFC, it just all of a sudden started doing this.

Thanks for your suggestion though, appreciated :)

Could be Ill add that to my list of things to check, thanks. Any other ideas?

When it "dies" it doesnt stall it just stops revving, tested it this morning and this time it sounded like its hit a rev limiter sort of thing. My main concern is that the light hooked up to the power fc to blink if theres a problem is coming on and staying on until a few seconds after i back off.

First test, put the Commander into Monitor mode and watch the display closely at 4,000rpm. It may pay to have the passenger do it or point the video camera at it then play it back for analysis later.

Second test, fuel filter and/or fuel pump, check the fuel pressure at the rail.

My best guesses :(

  • 4 weeks later...
Just as an update, the CAS was loose, tightened that up and the car hasnt played up since. It has also fixed the hunting for idle problem I was having too.

sorry to bring up a old thread and ask a dumb question, but what is the "CAS"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...