Jump to content
SAU Community

Recommended Posts

have gone the manual conversion route, leaving a few auto-related items for sale.

First is a valve-body upgrade for the RE4R01A transmission. This is all fully assembled so just needs to be bolted onto your transmission and good to go. The upgrade is based off a Transgo kit that has then been further tuned by KEAS; the shifts are wayyy improved from stock without being too clunky/jerky, just a nice quick shift that holds power with no flaring.

It's still in the transmission to keep everything nice n clean for the moment but hey, here's a pic of the complete transmission, just cos.... $200 for the valve body, and can post anywhere in Aus.

20181205_172907.jpg.fcbe6cf285be3628afd36f00e7f81865.jpg

The transmission itself; I believe one of the planet gears is slightly fkt, but still runs and changes gears excellently-like - just it develops vibration in 3rd gear around 90kph, which goes away when changed into O/D. The trans would be fine for a rebuild or for parts. $50, or will give away with the valve body for anyone local picking up the aforementioned item.

Furthermore; I have a B&M auto-transmission cooler (still on vehicle, to be removed shortly). This comes with mounting brackets and custom hard lines that will all bolt in place with no mods, on an R33 gtst in the driver's side behind-front-bumper-vent-area. Ditching the stock cooler that is mounted in front of the radiator massively decreased my engine coolant temps, in addition to the trans fluid being much more effectively cooled by the B&M cooler. The B&M cooler is also very robust, pretty sure you could whack it with a golf club and it would laugh it off (no I haven't tried it) so small stones etc from the road won't hurt it. Will be pulling it off this weekend and will post pics then. Looking for $150, once again can post aus-wide.

 

 

 

Link to comment
https://www.sau.com.au/forums/topic/475588-r33-auto-related-performance-items/
Share on other sites

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...