Jump to content
SAU Community

Recommended Posts

No unfortunately not, there is a seperate TCU (transmission control unit) required for the Jatco RE4R03A and the TCU HAS to match the ECU. A Gloria set would of course work.

Edited by Rusty Nuts

Have you got issues with the CVT?

Would need TCU + gearbox at a minimum. Not sure about ECU's. If you're in Aus there have been some wrecked Y34's, Import Nation parted one out a while ago.

Yeh I bought it really cheap with no gearbox the cvt broke and has been taken out. I’m looking on eBay and I can buy a ecu and tcu for the 4 speed but is ther any chance that would link up to any/most 4 speed jatco box’s because they are used in quite a few Nissan’s 

1 hour ago, Papuadij said:

I can buy a ecu and tcu for the 4 speed but is ther any chance that would link up to any/most 4 speed jatco box’s because they are used in quite a few Nissan’s 

No, the TCU's are matched to car and ECU and box, been down this road. But hey you don't need to believe me, just keep asking the same question a different way and somebody will give you the answer you want to hear.

As long as the ECU and TCU are for a RE4R03A  then you will need a speedo drive of the correct ratio to match your Diff the correct wiring loom and probably a dropping resister. Hopefully the Throttle position sensor for the CVT will be the same. If not one of those too. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...