Jump to content
SAU Community

Recommended Posts

All,

 

i am installing my walbro fuel pump this weekend. I understand the r34 gtt standard wiring uses a two stage fuel relay so on idle it cuts fuel or supply much less voltage (11v ) than 13.5 v.

 

my question is, i normally use a joint coupler with heat shrink covers. Is that ok inside a fuel pump? Obviously i will do the connection outsite of the fuel pump and then put it back in to the fuel pump.

 

i don’t think you can use electrical tape, can you ?

Link to comment
https://www.sau.com.au/forums/topic/475982-r34-walbro-255-fuel-pump/
Share on other sites

I'm maybe thinking more along the lines of a small I.D silicone fuel resistant hose (small motor fuel hose) line the exposed wiring/solder joint with something like https://www.supercheapauto.com.au/p/permatex-permatex-fuel-resistant-gasket-sealant-85420/356517.html and slip the silicone fuel resistant hose over it. the gasket sealant is non hardening so should keep even a slightly loose hose in place permanently as the sealant wont harden. Best I can come up with man hope it helps!

Thanks, will check it out

 

i am pretty worried on what happengs if positive and negative touch inside the fuel tank.

 

i think answer is spark and then boom. Have fine japaniese engeenering not thought of this?

 

even if fused, a small spark is enough to blow up the car with 60 liters of gas

 

re wire, i am thinking of soldering, what do you recon?

There can't be a boom in a sealed file tank even if the wires touch. No oxygen.

 

When I do pumps I offet the joints, so they can't touch and the use a piece of submersible fuel line over the positive joint. Like heat shrink but not shrunk.  None have exploded, so that's a pretty good result.

4 hours ago, drifter17a said:

If for whatever reason they do, screw coming loose?

 

lots of diy jumps simply use a wire connector so they could be setting up a death trap 

 

just amazed really on how stupied the design is

 

 

Too rich to ignite, even if you arched something inside the tank it won't ignite, even if created a physical spark it still won't ignite.

Engineers aren't stupid :)

 

8 hours ago, Dose Pipe Sutututu said:

Too rich to ignite, even if you arched something inside the tank it won't ignite, even if created a physical spark it still won't ignite.

Engineers aren't stupid :)

 

that is what I didn't know :)

 

well I was going mad getting all sort of sleeve to ensure they won't touch ...

5 hours ago, Ben C34 said:

If you don't believe us take off your petrol lid and drop a match in

will do later this evening, use my blow tourch .

 

i wonder why in the UK there is an old trick of calling the police and asking for a car to be removed which seems to have been abandoned by removing fuel cap and saying it is a fire hazard.

 

normally when the car is taxed( road tax) and MOT( mechanical check once a year) then they won't remove it but it if it annoying you people do above

 

14 hours ago, Ben C34 said:

If you don't believe us take off your petrol lid and drop a match in

Do not do this on a warm day, there will just enough fuel vapours and just enough air to ignite, just as the match goes down into the fuel neck lol

2 hours ago, Dose Pipe Sutututu said:

Do not do this on a warm day, there will just enough fuel vapours and just enough air to ignite, just as the match goes down into the fuel neck lol

Won’t go boom though.  Do it. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...