Jump to content
SAU Community

Recommended Posts

Hey guys,

Car is a r34 GTR.

Car runs perfectly fine, however after around 10-15 mins of driving, engine cuts out and turns off. This could happen while driving, or while on idle at a stop light. Sometimes I can start the car immediately, however most of the times, I cannot. I can turn the key to the on position (dash lights all operational, no check engine light), however cannot start. After waiting a few minutes, the car starts up fine and continues to drive normally until it cuts off again.

I'm thinking maybe a sensor is overheating, and cuts the engine completely. Maybe CAS? Maybe fuel pump relay? I'm not sure.

Temps on the MFD, oil temp, oil pressure, water temp etc are all fine. There's a little fuel pressure gauge in the engine bay, and it looks like it has constant pressure.

Car has a couple of recent mods: Haltech platinum pro, MAP sensors, upgraded cams, fuel pump + relay, intercooler, injectors, fuel rail, upgraded turbos and running e85. 

I had these mods for a good month before the symptoms above started appearing.

Any help would be much appreciated! Thanks in advance guys!

 

 

 

If it is a sudden stop it is likely to be electrical.  If it stumbles a bit it may be more fuel.  I once had a Falcon that would just shutdown after fifteen minutes or so - it was heat soak to an old coil.

Can you hear the fuel pump running when the engine stops?

  • 2 weeks later...

Thanks everyone for the help.

I downloaded the Haltech software and connected the car to my laptop. Monitored everything and realised the MAP sensor was flashing. 

Ended up being bad connection to the MAP sensor. We had to re-pin it and now works perfectly fine.

Thanks again! I hope this helps others out with their electrical issues!

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...