Jump to content
SAU Community

Recommended Posts

Hi. I hope to get some advice on my rebuilt neo oil pressure and a small oil leak..

After a catastrophic end to my engine months ago where timing belt idler came loose and fell off the head and some pistons got minced.

Anyways new head and rebuilt engine later.. 

First I want to ask if my oil pressure seems right. (New main bearings!!) Idle cold is 4.0Bar, idle hot is 3.5Bar, 4000Rpm goes up to maybe 4.5Bar. I have not hit high revs yet.. won't for a while! I'm using Repco 10w40 fully synthetic oil

Dash gauge being used! Not a proper gauge! So it won't be fully accurate!

Onto my little issue,

I am having a small oil leak from front of engine and cannot identify where it's coming from. It seems to pool to the right (passenger side) of the oilpump

I've once already tried to fix this by taking the radi out and the main pulley off to inspect behind timing belt cover.. tightening oilpump a little more. Also adding some more gasket glue to the sump/oilpump thinking the leak was that..

I honestly say that the timing belt is dry, the crankshaft timing belt gear and under it is dry (main crank seal is not leaking.., if it was leaking I think the inside the timing belt covers would be soaked?)

 

I saw a bit of oil from the timing belt idler pulley. The metal shaft of the pulley which bolts to the engine.. I saw a bit of oil under it, where it touches the block.. I don't know if it is flowing from there or somehow got some residual oil from the build! You know!! Oiling the bolts, and seals.. maybe it is not leaking there! (Won't know until I take off the covers again)

 

Has anyone ever had oil leaking from the bolt that holds the timing belt idler pulley?

Other then that I am thinking the oilpump/sump join is not sealed 100% or something..

But seeing oil as high as the idler pulley makes me think elsewhere.  It could be blowing around via the radiator fan.. / timing belt..

 

The cams are not leaking I'm 99% sure as it's bone dry that high!!

My dad keeps talking about blowby pressure being too high.. maybe making the oil seap.

Should I give it a week or two of driving and. See if this leak stops? 

 

Sadly the photos were taken 2 days ago when I had the bits removed.. it's now all complete and my test drive last night.. when I returned home.. had leak still..

 

Thanks.,

The image here shows the corner where it drops oil. (Passenger side corner front of sump)

20190523_111356.thumb.jpg.6c104c7a3901875e542caf30f6d6da2e.jpg

 

This photo shows the crank gear is dry? But the outside of the timing belt cover (right of pump is wet)

20190523_111421.thumb.jpg.bf05d14e49caa1b6d59ed49b1cfb8c57.jpg

 

This photo shows the water pump is dry.. (it is dirty. Didn't do such a good job cleaning inside the gap there!) so I am sure no oil is leaking from camshafts..20190523_111430.thumb.jpg.0158775742986f2cd2133133b261bcc2.jpg

Edited by ifixedit

The options for where the oil is coming from are innumerable. Diagnosing this without taking it apart, across the internet, is not going to be possible.

Could be leaking from the oil pump gasket. You might have damage on the front of the block where the idler bolt is - which wouldn't normally be a suspect except for how your engine died last time.

Needs at least partial dismantlery to find it.

Two things - you should run in a new engine with mineral oil not synthetic

- you should be pushing it from the get go - babying it will mean rings don't bed in properly and it will burn excessiveamounts of oil.

If you are pulling it down again put your stone down the bore and try to create a cross hatch again.

 

1 hour ago, ifixedit said:

Not babied.

Just don't want to full rpm boost until at least 100km.

First 20km were with semi syn. Some cheapish cheif oil to flush and clean. Now running the good stuff she leaks..

My RB30 was first started and the main break in done on the dyno c/w full power pulls. Then dump oil and put in another lot of mineral oil and driven for 6,000km. Then  the synthetic oil and another tune.

You don't want even semi synthetic oil because it prevents the rings from bedding in. If you pull your engine down see if the bores look glazed. You need to put pressure on the rings so with a hot engine don't be afraid to rev it. Do not labour it and keep an eye on the water temp and oil pressure and check for leaks. This has been best practice for at least 50 years.

Hi All,

I found the source of the leak.. turned out to be the bloody intake side Camshaft seal. 

when I installed the seal I did NOT place any gasket glue on the outer surface of the seal. Just a smear of oil for easy insertion.
Is it common practice to use gasket glue? or they go in clean? 

 

regards

Shaun

Edited by ifixedit
24 minutes ago, NEO25T said:

I put a bit of red rubber grease on the inside of the seal and a light smear of gasket maker around the outside, loosen off the cam cap a touch, push seal in and retorque the cap.

This might be completely wrong but it works for me.

NICE! :) 

thats what I will do :)

thanks bud

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...