Jump to content
SAU Community

Recommended Posts

Hi,

Some of you might know, I am preparing for my R33 modification (check the following link http://forums.skylinesaustralia.com/showth...=&threadid=4696),

however I need your advice; What sort of 550 cc injector for my modification? from I can see someone suggest 13B rotary injector, but does it need a new fuel rail? what can't use RB26 injector? consider cost and effect, what do you suggest?

thanks

Link to comment
https://www.sau.com.au/forums/topic/4772-550-cc-fuel-injector-for-rb25det/
Share on other sites

Guest Nismo_Freak

Word is that the CA18DET accepts the 550cc injectors from the RX7 very well. Since the CA18DET and the Skyline motors both utilize top-feed injectors the 550cc out of the 13B should just drop in. SR20DETs however use the side-feed injectors and are in their own boat.

hardly any1 with a RB25/RB20 has used a RB26DET injectors because of the Impedance difference.

GTR uses Lower OHM compaired to the RB25 (side feed)/RB20 (Top feed)/SR20 (side feed) which are higher.

You can bring down the ohm by buyin a resistor back.

I would suggest to buy some nismo or bosh ones so that go in quiet easy into your car.

Depending on the application you may considar the use of GTiR or JDM S15 injectors, which are 470 or 480cc...fit straight in.

Of course this depends on how hard you intend to tune the car.

The Rotary ones require fuel rail mods and a few other setup mods.

A good fuel pressure regulator with the JDM/GTiR injectors would probably work very well.

Or you could go and try get some Sard Injectors off the jap auctio websites, they too fit in, but may require some wiring impedence mods

Thanks for all the input..

From the following url, it does confirm SR20DET and Rb25DET use the same injectors, both side feed, but might have long and short difference (not sure what it is? someone got clue?)

http://www.dspeed.co.jp/english/others/mot...er/m_o_inje.htm

  • 3 months later...

After searching for injectors I came accross this old thread which is relevant to my question.

Today I was at my mechanics asking him how I could get some more power out of me s2 r33 gtst.

He said he would sell me his r33 gtr injectors from his own car and would get them serviced and installed for about 80-100$ each.

He also said he would sell me a fuel pump for about $300 fitted, and lastly he would sell me a fuel pressure regulator for about $160.

All up about $1200.

My aim is to get high 12sec for 1/4mile which he said would be possible with my current mods (turbo back exhaust, hi flow cat, high flowed turbo, pod, FMIC, profec b EBC which will probably be set around the 1bar mark) and a powerFC which will follow after I get fuel right.

Does anyone have suggestions or comments on what i'm planning on doing because i'd love some feedback if i'm making a mistake.

Mark

no need for injecotrs for a high 12

plus the gtr injecotrs wont work on an rb 25 you will need a new fuel rail and they are only 70cc's bigger plus they are the wrong impedance and type they are top feed rb25's are side feed

a bigger fuel pump with adjustable reg and power fc

should give you 220 rwkw plentyof people here have done it

meggala

MRK25T, you really should think about your management before you start worrying about your fuel. With an aftermarket ecu fitted, and a fuel pressure reg with stock injectors you should be able to push 250rwkw - as I know of someone who is currently at 257rwkw with the stock injectors. The stock ecu thinks you have stock injectors, so if you upgrade your injectors with out the ecu (or an SAFC) you will be running very rich = less power and lots of black smoke.

If you want to go top feed injectors, you will have to replace or modify the stock plenum and then get a new fuel rail. Thing to remeber is that side feed high impedance injectors are bloody expensive - top feed high impedance are reasonably cheap, you can pick up top feed injectors quite readily for approx $75, side feed dont expect much change from $250+.

Steve,

I was going to get my car boosted, get the fuel system installed, and get the powerFC installed and tuned at the same time.

I think it will work out cheaper if I get it all done at once instead of staggering it (both in time without the car and money).

My profec B is on its way from Nengun, I now need advice what parts I need now.

Thanks Steve and Meggala

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...