Jump to content
SAU Community

Help me with my r33 gtst


Recommended Posts

Guest Slide

Somebody help me!!!!!!!!!!!!!!!!

I have taken my R33 to a number of stupid so called specialists and they have all given me different answers which have cost me nearly $2000.

On standard boost (7psi) it runs like new ,Anything over (i mean even 1 psi over) it pops not detonates. it sounds like it is backfiring.

it looses boost and it sounds like it is just feeding it out the exhaust. verrrry embarassing.

sound like it is farting. I am using a turbosmart dual stage boost controller (tried a different 1 already) 750hp fuel pump, ngk irridium plugs,fuel lines, injectors have been cleaned ,3'' turbo back exhaust, pod filter ect. I have tried tripping the computer did not fix.

Help Help Help (eeeger to run more boooost) i feel like popeye without spinach

Link to comment
https://www.sau.com.au/forums/topic/47752-help-me-with-my-r33-gtst/
Share on other sites

Sounds like boost cut to me.

How are you measuring boost? Boost cut happens at about 10psi or a bit over. The symptoms match pretty much exactly what you described.

You could get a boost cut defender but you're better off getting a full ECU replacement.

Guest Slide

anything after 7psi confussed everyone i sent my car to

people have said to me the following with reports.

1:change computer

2:change bov(i am still using factory plum back)

3:change boost actuator

4:change plugs (so i did)

5:fuel pump (so i did)

6:have injectors cleaned(they were left to recirculate for 13 hours)

have tried using tape over the coil packs to avoid shorts from faulty coil packs.

i have taken it to 2 places where i have said i am not paying unless it is fixed came back and they both said cant help you.

Someone please give me an answer.

I am a Gold Coast local.

Anyone know anything

If someone knows a servicer around my area please post

  • 1 year later...

funny, i always thought my car was spiking, but the symtops you show are exactly what im experiencing???, so its missing big time.

Im havnig the exact same problem mate!, anything over stock 7psi (or 1/2 way on the stock gauge), will start missing, feels like 100 times a second, and yes fartings a good word:)

just wondering if you've overcome the issue yet? do i really need a safc???

I think Robo is onto something... you need to get it dynoed and post up the A/F ratios etc... my bet would be its just running extremely rich and blowing out your spark... remember the closer you gap your plugs the weaker the spark gets (may help you fix the problem in the short term tho)

other than that if you reckon it is losing boost could you just have a boost leak somewhere that only become apparent when you go over 7psi?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...