Jump to content
SAU Community

Recommended Posts

Hey guys,

Haven't posted in a while and bit disappointed that it isn't on better terms but don't believe it is a major problem.

Just wanted to query whether anyone has had similar issue to what i am experiencing with my power windows.

Currently, Drivers side window works perfectly, no issues, goes up and down all day, however the passenger side - i had intermittent issues with window not wanting to go back up.

Window will go down fine, but will not go back up.  There were a couple of days where it would then wouldn't go back up.

Things i have tested and done:

 

  • Changed plug from harness that connects to regulator as it was a bit corroded looking - no change
  • tried another regulator, which had been tested with direct power - works perfectly - fitted it and no change
  • Also then put direct power to regulator i had pulled out initially and it is fine.
  • Both switches from driver side and passenger side will operate passenger window to go down, but not back up.
  • Fuse is obviously okay, as nothing would work if it was blown.

My query is and next thing i am going to check is the window relay (black box in drivers door):

Can this be a possible cause of window going down but not back up and have not affected drivers window? 

 

Any help is much appreciated.   i just guess it would give me a bit of reassurance if someone has been in exactly the same boat and confirmed the relay was stuffed.

 

 

 

 

 

Isn't it far more likely that the up contact on the switch is faulty? Dirty/burnt/broken off/etc?

The left-right switches are connected. Look at the wiring diagram to see how. I think if one is dead, it can take down both.

Edited by GTSBoy

I would of thought the likelihood of both drivers and passenger side switches that operate the passenger window to go up, to be faulty/dirty/burnt/broken to be slim.   but not to say that it has happened. 

Plus the other thing that didnt make sense, is the switch on the passenger door, i had put multimeter on the plug to see that 12volts was getting to the regulator and both going up and down did register 12 volts. 

Might see if i can locate new switches anyway.

But i guess.  could there still be possibility of the relay causing a similar issue?

 

Yes, the relay could have a fault. But I didn't say both switches would be dead. It only takes one dead to kill it. Usually the one that gets the most use, but could be either.

And I wasn't recommending new switches. Take them apart and see what condition they're in.

Edited by GTSBoy

So contacts on switches - if going up on one is stuffed then both switches wont operate the window to go up?

Sorry my electrical expertise is not the greatest.

I have spare switches at my old mans place, so can try them and see what happens.  Will have a squiz at the switches too and see condition.

also got spare relay too.  so will try those two things and see what happens.
 

3 hours ago, bazr33 said:

So contacts on switches - if going up on one is stuffed then both switches wont operate the window to go up?

Yeah, I'm pretty sure that the way they are wired is not as simple as you might imagine, and it leads to one dead all dead, like old xmas tree lights.

f**ks me what’s going on.. whether it will lead to intermittent shit.. old wiring.. bad contacts.. but got it working.. 

 

whether I did some sort of reset.. but will wait for it to f**k out again.. see what happens 

  • 3 weeks later...

I spent the past 4 years chasing the same issue on a s14.

I completely pulled the switch apart a good 5 times and cleaned the contacts. The switch tested fine every time. Everything tested fine. Just ended up jumping the passenger switch closed at the plug and used the drivers side switch. 

It was one of the little contact arms that gets pressed down when the switch is worked wasn't bending enough when voltage is applied.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...