Jump to content
SAU Community

Recommended Posts

Hi All,

My car have been sitting for years with fuel in the tank and the fuel actually smells pretty bad..

Has anyone cleaned out their fuel tank before? or know of any places that can clean it? I got a quote from a place and they said $399 to get the tank cleaned lol

Any help/recommendation would be highly appreciated.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/481287-gtr-r32-fuel-tank-cleaning/
Share on other sites

Yep I have cleaned multiple fuel tanks as I have cracked a 32 GTR fuel tank more than once. You're talking about the molasses like shit left from unleaded fuel right ? No, unleaded will not move it like you would think. After much trial and error -

Bleach. Doesn't react with the HDPE the plastic tank is made out of. The bleach bottles are made out of the same material. Get about 8 - 10 litres, leave overnight. Swirl and agitate next day as required. It will bring it back to new.

  • Like 1
39 minutes ago, BK said:

Yep I have cleaned multiple fuel tanks as I have cracked a 32 GTR fuel tank more than once. You're talking about the molasses like shit left from unleaded fuel right ? No unleaded will not move it like you would think. After much trial and error -

Bleach. Doesn't react with the HDPE the plastic tank is made out of. The bleach bottles are made out of the same material. Get about 8 - 10 litres, leave overnight. Swirl and agitate next day as required. It will bring it back to new.

Set for it, thanks mate ??

16024003665641214337333073242163.jpg

  • Like 1

Fully serious. Test it on a gummy hose clamp or something else from your tank. It will strip the crap off everything. Obviously make sure your tank is pressure washed afterwards and left to dry, as the last thing you want in your fuel system is bleach. Results may vary depending on the crud in your tank, might need more but it's a good start with 8lt and will 100% work. Please post results for confirmation as I've seen no one recommend it before and has proven for me to be the only sure way that works. If you can seal the tank and invert it even better, as getting it off of the bulkhead area is the hardest part. Good round up weed killer substitute afterwards.

  • 4 weeks later...
On 11/10/2020 at 7:19 PM, BK said:

Fully serious. Test it on a gummy hose clamp or something else from your tank. It will strip the crap off everything. Obviously make sure your tank is pressure washed afterwards and left to dry, as the last thing you want in your fuel system is bleach. Results may vary depending on the crud in your tank, might need more but it's a good start with 8lt and will 100% work. Please post results for confirmation as I've seen no one recommend it before and has proven for me to be the only sure way that works. If you can seal the tank and invert it even better, as getting it off of the bulkhead area is the hardest part. Good round up weed killer substitute afterwards.

Hi mate,

Here's the results and the process;

1) Empty the old fuel and dispose

2) Degrease the fuel tank inside out

3) Pressure wash is multiple times

4) I put in 12l of bleach and shake the fuel tank to make sure it reaches everywhere

5) Left it overnight and came back the next day and pressure washed it again, and again and again lol 

6) Air dryed

7) Cleaned the outside of the tank and give it a fresh coat of satin black paint

 

20201101_132340.jpg

20201101_132352.jpg

20201103_070120.jpg

20201103_070134.jpg

20201103_070138.jpg

  • Like 1
  • 2 years later...
On 10/11/2020 at 5:33 PM, BK said:

Yep I have cleaned multiple fuel tanks as I have cracked a 32 GTR fuel tank more than once. You're talking about the molasses like shit left from unleaded fuel right ? No, unleaded will not move it like you would think. After much trial and error -

Bleach. Doesn't react with the HDPE the plastic tank is made out of. The bleach bottles are made out of the same material. Get about 8 - 10 litres, leave overnight. Swirl and agitate next day as required. It will bring it back to new.

Many thanks @BK!

Put in 10L of bleach, sloshed it around every now and again over 24 hours. Pressure washed it after draining the bleach out. Not perfect, but massive improvement and happy with the results. Pics below, the tank was still wet when I took the before and after shots.

 

Before:

Before162518.thumb.jpg.c011184c809f668f972d695089eb6557.jpg

Before162527.thumb.jpg.8ed645bdbd216cb68d284da15a4764e4.jpg

Before162538.thumb.jpg.e4bd3ffb7ff882cf56bf6cd31bb6dc2e.jpg

 

After:

After173741.thumb.jpg.f64cd3c53e567aa49fecaeefe7998d44.jpg

After173841.thumb.jpg.18169a61f0dab6dd43e0bf3da127ea33.jpg

After173752.thumb.jpg.e057aa414dd50aa9f8af7c14ecc8afa7.jpg

After173802.thumb.jpg.b1bff18790c19847f5920371a92e0826.jpg

  • Like 1
On 13/01/2023 at 1:19 PM, Zurlox said:

Many thanks @BK!

Put in 10L of bleach, sloshed it around every now and again over 24 hours. Pressure washed it after draining the bleach out. Not perfect, but massive improvement and happy with the results. Pics below, the tank was still wet when I took the before and after shots.

 

Before:

Before162518.thumb.jpg.c011184c809f668f972d695089eb6557.jpg

Before162527.thumb.jpg.8ed645bdbd216cb68d284da15a4764e4.jpg

Before162538.thumb.jpg.e4bd3ffb7ff882cf56bf6cd31bb6dc2e.jpg

 

After:

After173741.thumb.jpg.f64cd3c53e567aa49fecaeefe7998d44.jpg

After173841.thumb.jpg.18169a61f0dab6dd43e0bf3da127ea33.jpg

After173752.thumb.jpg.e057aa414dd50aa9f8af7c14ecc8afa7.jpg

After173802.thumb.jpg.b1bff18790c19847f5920371a92e0826.jpg

No worries, good job. If you persisted for days you would've got that solid stuff off but it does look pretty caked on. Might have needed to use a solvent for that last bit then rebleach to get it 100%

Looks good anyway 👍

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...