Jump to content
SAU Community

Recommended Posts

ok guyz..i got a problem..a serious problem...

i was wondering if u guyz can help me?

ok i bought my GTR on tuesday ;)

i had to jump start it cuz it hasnt been driven for 2 weeks.

once i jumpstarted it ,i was on my way home.

around liverpool about 30mins into my journey home....

the car just shut it self off in the middle of the road..

making my GTR look like a POS :D

anyway...i manged to push it off to the side of the road and bought new batteries..and replcaed it on the road...the car fired up after the replacement battery...i gave it a bit of rev..

it'll rev till 5K and then stop..once i drop the revs the car will shut it self again...

only this time i can start the car over and over again.

i managed to get it through the busy sydney traffic and to my mechaics place..

today after 2 days i've bought it...the AFM's once though were at fault were not at fault nor the ECU

now i am really running out of ideas...

i was wondering if any1 could help me..

currently the car is running super rich blowing balck smoke like a chimney

and refuses to rev past 3g the car it self has done less than 500 KM's since brought in.

Link to comment
https://www.sau.com.au/forums/topic/48153-help-my-car-is-screwedfunny/
Share on other sites

  • 4 months later...

danny i think its the throttle body being dirty...

u got new batteries and also got spart plugs replaced

which means the throttle body is dirty..

u can clean the trottle urself.... only need a tooth brush and some trottle body cleaner

and it shouldnt do it again... if it does then i dont hab a clue

unless u got the wrong batteries

First things first your car only has one battery. There is no way that it will be your throttle bodies (yes you have 6) the rb26 has a multi throttle body setup to enhance throttle response. Throttle bodies being dirty wouldn't be an issue. In extreme cases they mite hamper performance if the airflow is being restricted, but in no way could they cut the engine completely. The chance of it being an o2 sensor problem is also slim as they only trim the mixture. id more inclined to check for air leaks after the afm's in all the intake plumbing that would make it run rich but i doubt it would completely cut out. It depends on how much has been modified on the car too. Like sumone said it could be the ECU especially if its an aftermarket unit playing up. Best thing to do is take it to a fuel system expert.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...