Jump to content
SAU Community

Recommended Posts

My partner's 2004 350gt skyline won't start we just started it to move it into the shed then we went to turn it on again and now it won't start we have lights coming on and everything but won't crank all it does is buzz 

We have tried the starter motor it's not that 

Check fusses not that 

And we have checked the battery not that 

And also check fuel pump it's not that 

This has just happend out of no where it hasn't done this before and it's our daily 

Link to comment
https://www.sau.com.au/forums/topic/481656-my-partners-car-wont-start/
Share on other sites

It does sound like a battery, when you attempt to crank, do the lights on the dash stay on at full brightness? or do they go very dull/off?

If they stay on full, it points more toward the starter motor, if they go very dull, then look more toward the battery.

How have you eliminated the above items?  replaced them?  tested them?

  • Like 1
1 hour ago, sonicii said:

it points more toward the starter motor

Whoa back up son, the starter motor is actuated by a relay have you checked the relay? Have you applied power directly to the starter motor? Does it rotate? Does the solenoid actuate ? Does the relay click, or is that your Buzzing sound. Are you sure the battery is ok, you must load test batteries a simple voltage measurement is not good enough.

  • Like 1
On 12/16/2020 at 10:33 PM, Rusty Nuts said:

Whoa back up son, the starter motor is actuated by a relay have you checked the relay?

For sure, when I say 'point toward the starter motor', I don't mean it will be the starter motor, but including all the components associated with it, including relays, wiring, grounding, etc.

  • Like 1

FWIW my M35 cranks hard even when it doesn't have enough electric power to start. First thing i'd do it try a jump start after double checking battery connections and charge. IIRC the battery should be 12.6 volts when fully charged.

just making sure you have checked the connections to the starter that the nut or clip may be loose? wiring maybe to the plugs to the starter. and yeah of course make sure you have voltage or try boosting it with another vehicle. kick the bitch a little bit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...