Jump to content
SAU Community

No wheel speed all of a sudden?

Blakeo
 Share

Recommended Posts

Blakeo Rising Star

Blakeo

Posted
Posted (edited)

1996 R33 Skyline GTS25T, NON ABS MODEL. 

Up till a couple months ago ecu was displaying wheel speed well. For some reason now it is no longer showing it. Only thing I have touched wiring wise is cutting a wire for the hicas ecu which puts the hicas light on the dash after installing a delete kit. 

Wheel speed still works on the dash, but my boost by gear etc no longer works due to ecu not seeing wheel speed. 

I am going to try and reconnect this wire tomorrow and see if it fixes the issue. 

The Yellow/Green wire on the ecu is for Vehicle speed and probing it with a multimeter in ac or dc mode, it does not give a reading. 

Any ideas? 

Edited by Blakeo
Link to comment
https://www.sau.com.au/forums/topic/482300-no-wheel-speed-all-of-a-sudden/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

So, we're not talking about wheel speed here. VSS is on the gearbox, not a wheel.

The VSS sends an AC signal to the speedo head, where it is converted to a PWM (square wave) 0-5V signal that the ECU, HICAS, TCU, etc all read on the vehicle bus.

If you want to measure the presence of that signal at the ECU it is best done with a scope of some sort, rather than a multimeter, as you won't reliably see it with a meter.

The speedo head might be faulty.

Blakeo Rising Star

Blakeo

Posted
  • Author
Posted
1 hour ago, GTSBoy said:

So, we're not talking about wheel speed here. VSS is on the gearbox, not a wheel.

The VSS sends an AC signal to the speedo head, where it is converted to a PWM (square wave) 0-5V signal that the ECU, HICAS, TCU, etc all read on the vehicle bus.

If you want to measure the presence of that signal at the ECU it is best done with a scope of some sort, rather than a multimeter, as you won't reliably see it with a meter.

The speedo head might be faulty.

Hm ok, I don't have a scope. Is that something an auto electrician can sort out? 

When you mean the speedo head has a fault, but wouldn't the dash not be working then because both take inputs from the same sensor on the gearbox? I think I can role out a fault with the sensor on the gearbox? 

Waiting to hear back from Link support too, wondering if it could be an ECU issue. 

GTSBoy Grand Master

GTSBoy

Posted
Posted
5 minutes ago, Blakeo said:

When you mean the speedo head has a fault, but wouldn't the dash not be working then because both take inputs from the same sensor on the gearbox?

There is circuitry to take the AC signal from the sender and make the needle move. That appears to be working. There is other circuitry that takes the AC signal from the sender and transmits it as the PWM signal on the bis. That could be borked. It happens.

Blakeo Rising Star

Blakeo

Posted
  • Author
Posted
On 4/19/2021 at 2:36 PM, GTSBoy said:

There is circuitry to take the AC signal from the sender and make the needle move. That appears to be working. There is other circuitry that takes the AC signal from the sender and transmits it as the PWM signal on the bis. That could be borked. It happens.

Where abouts would that circuitry be? There's four wires coming off the back of this VSS on the gearbox. 

1 I have traced back to the cluster (the circuitry to convert it to dc for the needle, must be built into the dash cluster?) 

The green/white wire, I have traced goes over the gearbox under the back of the motor and ties into the ecu harness. From there I lose it, because otherwise I will need to strip the harness down. 

But I believe your right, because this green/white wire is not the same color as the one at Pin 29. 

Any ideas, I'm lost and most auto electricians near me are booked out a month in advance atm. 

robbo_rb180 Grand Master

robbo_rb180

Posted
Posted

so Speedo works on the dash but ecu doesn't detect non-driven wheel speed?
What ecu? probably using one of the abs sensors for non-driven speed and you have now modified the circuit as some ecu require a digital input not Ac as most abs sensors are.

what happens when you reconnect the wire you cut?

Blakeo Rising Star

Blakeo

Posted
  • Author
Posted
23 minutes ago, robbo_rb180 said:

so Speedo works on the dash but ecu doesn't detect non-driven wheel speed?
What ecu? probably using one of the abs sensors for non-driven speed and you have now modified the circuit as some ecu require a digital input not Ac as most abs sensors are.

what happens when you reconnect the wire you cut?

Hi Robbo, 

As per my original post mate the car is a Non-ABS model. The vehicle speed comes from the gearbox. This is shared to both the dash and ecu. 

No difference, the wire I cut was for the HICAS warning light after reconnecting the warning light come back on the dash but still ECU doesn't pickup wheel speed as it did before. 

I am using a Link G4+ ECU, Link support has been very good and we have narrowed down the issue to be wiring but due to my inexperience I can't trace where that green/white wire goes. Currently considering a new old stock wiring harness my local Nissan dealer has in stock.. 

robbo_rb180 Grand Master

robbo_rb180

Posted
Posted

It's in the loom between the dash and ecu. There is a plug that won't be seated properly as has been mentioned the dash does the conversion from the speed sensor then a wire goes to a connector near the ecu. 

No need for a new old stock loom. Find the plug and check it or remove the cluster find output pin and run a new wire to the ecu. 

I'll try and get a picture of the connector in the morning 

robbo_rb180 Grand Master

robbo_rb180

Posted
Posted (edited)

Have had issues in the past with Rb to s chassis conversion wiring with the that dash output not connected and speed needs to be connected for things to work correctly. 

 

Pin 53 is speedo input on Rb25 ecu

1211552313_images(3).thumb.jpeg.42faf08a5779dcad9e773703e2e7a72b.jpeg

Double check connectors here and back of the cluster. 

Edited by robbo_rb180
Add info
Blakeo Rising Star

Blakeo

Posted
  • Author
Posted
1 hour ago, robbo_rb180 said:

Have had issues in the past with Rb to s chassis conversion wiring with the that dash output not connected and speed needs to be connected for things to work correctly. 

 

Pin 53 is speedo input on Rb25 ecu

1211552313_images(3).thumb.jpeg.42faf08a5779dcad9e773703e2e7a72b.jpeg

Double check connectors here and back of the cluster. 

Hey mate, I've just pulled the cluster out of my car, but can't find any connects like that behind it? 

I've had a search around the ecu in the passenger side kick panel and can't find it either. I'm starting to feel really stupid - Or I am hoping I don't need to take the whole dash out to access that plug? 

Blakeo Rising Star

Blakeo

Posted
  • Author
Posted

Issue sorted, I ended up having to pull the whole dash out of my car and replacing the heater core. 

Heater core must've exploded or been leaking for a bit. Soaked those connectors in question with coolant, took it all apart cleaned it out with contact cleaner. Replaced the heater core made sure it doesn't leak and put it all back together and have my speed signal back.  

Replace those heater cores guys, they're getting too old now lol. 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
×
×
  • Create New...