Jump to content
SAU Community

RB20DET Code 34 even after knock sensor bypass

Blaeeeek

By Blaeeeek,
in General Maintenance

 Share

Recommended Posts

Blaeeeek Newbie

Blaeeeek

Posted
Posted

Hey fellas. 

Since I bought my HCR32 it has ran pretty well although it runs rich and sucks down fuel. I checked the codes and it throws a code 34, knock sensor and a code 21, ignition signal. I heard that when code 34 is thrown the ECU will retard timing and dump in fuel. 

 

I went ahead and bypassed the knock sensors for diagnosis purposes. I went down to the ECU and soldered 1/4 watt 1M ohm resistor on each of the two wires for the two knock sensors, and grounded the other ends to the chassis. 

 

After doing so, I went and test drove the car and I could feel a slight hesitation around 5-6k rpm or so, which it didn't do before. It feels like it maybe is slightly slower after said hesitation, perhaps the ECU pulling timing. However, it didn't do this prior to me bypassing the knock sensors. 

 

Got back home, checked the codes, and code 34 once again showed. If I bypassed the sensors with the resistors I would think it's not possible to throw that code. 

 

My question is, is the hesitation pulling timing, and it actually wasn't pulling timing before the bypass like I thought it was? Or could it have been pinging that I felt? I'm not sure exactly what pinging feels like as I've never experienced it. 

 

Perhaps my rich/awful mpg issue is something else and this was all a waste of time. Let me know what you guys think, thanks 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Rezz
      WGNC34 - floor mats

      By Rezz · Posted

      I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...