Jump to content
SAU Community

Recommended Posts

Hey Sau,

Long time lurker. I just wanted some opinions from the experienced guys to see if this block is still useable or if it's a boat anchor and I should try get my money back? My concern is this crack between the water jackets to the head bolt thread between cylinder 3 and 4 see picture attached. Little back story about it, I bought it as the start of a small build to put into my daily. Was told was running fine no issues the previous owner had just pulled it down to go forged bottom end lost motivation and was now selling if off, after I started to clean it up I found the crack. The target I'm aiming for would be between 375 - 450kw so not the biggest power output but as it's going into my daily ( probably in the year 2050 at this rate) I'd like to give it a chance at surviving for as long as possible. 

crack in deck rb26.PNG

As far as I know the spot that breaks most commonly is on the exhaust side, adjacent to #4 or between 4/5. So any unnecessary weakness on the exhaust side, even if it's not is the "usual" spot, can't be a good thing. And between 3 & 4 is not so far away from where the block likes to jump to pieces.

Thanks for replying so quickly and sharing your knowledge. I had heard of the block issues between cylinder 3 and 4 splitting and the crack on the outside of the block from block twist after a healthy amount of power put through them but this is all new to me. When I spotted it I thought it might be a drama but was hoping it was more superficial so I could finish making the deck flat give it a hone and get down to ordering some parts, looks like I might have to start getting in touch with the seller to try get my cash back. 

Mine has a crack from water gallery to headstud hole in-between 5&6... Sent it back together, been a year so far at 520kw and had no dramas yet .. I guess it all depends if you are prepared to do all that work to potentially do it all again 🤣

Edited by BrynDETT
  • Like 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
Ă—
Ă—
  • Create New...