Jump to content
SAU Community

Recommended Posts

16 minutes ago, GTSBoy said:

Only if the CHRA is completely cracked through. Which doesn't happen.

only way really to find out is if I Dona coolant pressure test, disconnect the oil drain and see if coolant leaks from there?  Or the other option head gasket? But very unlikely as I just replaced it which leave maybe piston bores have a hairline crack? I dunno lost for words now. 

 Did a compression test and all cylinders were even. 
4 things come to mind.

1. Head gasket - which I just replaced, MLS 12mm with copper spray for extra seal. (Not losing coolant )

2. CHRA - leaking through turbo drain and into sump ( coolant pressure test will confirm this tomorrow )

 

3. cracked head ( been repaired and machined. ( didn't even reach operating temp before unnoticed coolant in oil pan)

 

4. block (piston bores cracked) 

more investigating 🤦🏽

Edited by VL_Turbo
14 minutes ago, GTSBoy said:

No. That makes it more likely.

Thinking of maybe replacing the Nitto MLS gasket and replacing it with a Genuine Nissan head gasket. 
 

only went Nitto MLS due to it being a 1.2m thickness to reduce comp. 

you never needed to reduce comp, but anyway.

 

How sure are you that the block surface was  all good ? It is a nightmare getting old gasket off. how did you do it?

copper spray isnt a normal thing to do. how much did you spray on? Have you done that before?

 

 

the chances of the turbo being the issue are so slim, but you may as well check.

1 minute ago, Ben C34 said:

you never needed to reduce comp, but anyway.

 

How sure are you that the block surface was  all good ?
(used knife sharpening block)

 

It is a nightmare getting old gasket off. how did you do it?

( knife sharpening block and sand paper on a block with wd40 and brake cleaner)

copper spray isnt a normal thing to do. how much did you spray on? Have you done that before?

3 layers of copper spray, no, haven't done it before.

( wouldn't compression test eliminate all this, came up good all the cylinders were even?

 

1 minute ago, Ben C34 said:

 

 

the chances of the turbo being the issue are so slim, but you may as well check.

 

Can you take us back to the start? Why were you doing the head gasket in the first place?

It is possible to get simple things wrong in this job....

Did you check every hole in the supplied head gasket matched the block and head orifices?

What procedure did you follow to tighten down the head? Do you know your torque wrench is calibrated properly? Are the head bolts still tight now? 

Also I remember something about some blocks and needing to seal studs to the water jacket, not sure if that was rb30 though

1 hour ago, Duncan said:

Can you take us back to the start? Why were you doing the head gasket in the first place?

It is possible to get simple things wrong in this job....

Did you check every hole in the supplied head gasket matched the block and head orifices?

What procedure did you follow to tighten down the head? Do you know your torque wrench is calibrated properly? Are the head bolts still tight now? 

Also I remember something about some blocks and needing to seal studs to the water jacket, not sure if that was rb30 though

Runt too much boost on a hot day with nearly 300,000ks on the motor. Old head gasket was worn out.

with the head bolts I followed the Gregory's manual. Used head stud and lube on the head studs.

 

will take rocker cover off and recheck the torque, I believe it was 97nm for head studs. 
 

no idea about what you mean to seal head studs to water jackets?

15 minutes ago, VL_Turbo said:

no idea about what you mean to seal head studs to water jackets?

Some head studs' drilled and tapped holes go through to the water jacket (On some motors. And Duncan was saying he didn't recall if RB30s were one of them, and I don't think they are).

On those motors you can't just screw them in, you have to apply thread sealant before you put them in to stop coolant coming up the bore of the stud hole and arriving in places where it is not supposed to be.

We might be able to advise you better with more detail. When you say 

46 minutes ago, VL_Turbo said:

Runt too much boost on a hot day with nearly 300,000ks on the motor. Old head gasket was worn out.

What did you notice happened, and what have you done since? For example,

did the car run hot?

did oil/water mix in the engine, and if so how did you flush the block, oil cooler (if fitted), oil/water interchange (if fitted), radiator?

did you use new head bolts/studs?

did you get the head checked for straightness?

after you prepped the block surface with a sharpening block/wd40, how did you check it for straightness?

46 minutes ago, VL_Turbo said:

with the head bolts I followed the Gregory's manual. Used head stud and lube on the head studs.

will take rocker cover off and recheck the torque, I believe it was 97nm for head studs. 

- what was the procedure you followed, did you tighten then down in steps and was there an order to tighten the bolts from middle to outside?

21 minutes ago, Duncan said:

We might be able to advise you better with more detail. When you say 

What did you notice happened, and what have you done since? For example,

did the car run hot?

Ran to half temperature, didn't get hot. Turned it off.

did oil/water mix in the engine, and if so how did you flush the block, oil cooler (if fitted), oil/water interchange (if fitted), radiator?

coolant and oil did mix, flushed the block via a bolt under the coolant line for the turb. No oil cooler fitted. But I did install a new trans cooler so avoided trans line connected to radiator. 

did you use new head bolts/studs?

Yes, new ARP head studs and bolts 11mm.

did you get the head checked for straightness?

yes, crack tested, pressure tested, new valve stem seals.

after you prepped the block surface with a sharpening block/wd40, how did you check it for straightness?

checked with a straight edge.

 

Done compression test came up as follows

1- 111psi, 2- 115, 3-119, 4- 120, 5-120, 6- 115

 

done coolant pressure test and not leaking or losing coolant and definitely not losing coolant via turbo drain. Puzzled is understatement atm.😳

The extra detail does help. What was it that made you check for a headgasket issue in the first place if it never got hot?

I'm thinking it might be fine and the milkshake is just from the original failure. Try changing the oil again and see if it is getting better or still bad.

The coolant pressure test is a good check but it can miss an issue which only occurs when hot or at much higher pressures (like compression pressure)

  • Like 1
1 minute ago, Duncan said:

The extra detail does help. What was it that made you check for a headgasket issue in the first place if it never got hot?

alot of white smoke came out of exhaust.

I'm thinking it might be fine and the milkshake is just from the original failure. Try changing the oil again and see if it is getting better or still bad.

I'll get new oil now.

The coolant pressure test is a good check but it can miss an issue which only occurs when hot or at much higher pressures (like compression pressure)

I'll put new oil and leave it idling for 10-15 mins, will have to bed the new cam in as well. (Stage 2 Kelford 226F).

 

2 hours ago, Duncan said:

absolutely, either a specific product or just throw some diesel in with the oil for 5 minutes.

I bought Penrite flush oil. Went online and I was told it can harm the engine?

this is my Nitto 1.2mm multi layer steel head gasket, can only go on one way right?

D646BA98-8CC8-4AF5-9B48-61A6D3FBFA8F.jpeg

Edited by VL_Turbo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...