Jump to content
SAU Community

Recommended Posts

Hi,

if had the car for around 3000km now. Since the last 750km the transfer case started to leak. I have degreased it a few times and after a drive the drips are already hanging under the case. It’s red of color so I am sure it is ATF fluid. The case or gearbox has not been removed. I did change the gearbox oil to redline to get rid of a grind in fourth, but thats it. What are the most common causes of these cases to start leaking? 
 

Also when shifting I feel the car does a hard clunk even when letting the clutch get up slowly. Its like something gets a snap due to getting power from the engine. If that makes sense.

 

Hope someone can narrow it down for me. Can’t get the car in the air to verify more. Would need to go to a shop for that. 
 

cheers! 

C29372EA-2475-4AF5-892A-8D1CAB66725C.jpeg

14C6A8F0-4E6E-4F9F-A075-6E10D3B85D78.jpeg

4244E698-97EE-410C-89E0-EB3D3DD019F4.jpeg

Edited by T.Krol
Spelling error
1 hour ago, T.Krol said:

Hi,

if had the car for around 3000km now. Since the last 750km the transfer case started to leak. I have degreased it a few times and after a drive the drips are already hanging under the case. It’s red of color so I am sure it is ATF fluid. The case or gearbox has not been removed. I did change the gearbox oil to redline to get rid of a grind in fourth, but thats it. What are the most common causes of these cases to start leaking? 
 

Also when shifting I feel the car does a hard clunk even when letting the clutch get up slowly. Its like something gets a snap due to getting power from the engine. If that makes sense.

 

Hope someone can narrow it down for me. Can’t get the car in the air to verify more. Would need to go to a shop for that. 
 

cheers! 

C29372EA-2475-4AF5-892A-8D1CAB66725C.jpeg

14C6A8F0-4E6E-4F9F-A075-6E10D3B85D78.jpeg

4244E698-97EE-410C-89E0-EB3D3DD019F4.jpeg

Transmission or engine mounts need to be replaced if you get bad shift shock even with a lot of clutch slip. The back of the transfer case is probably leaking where the hose connects. It’s a high pressure hydraulic system so leaks are inevitable with age. To be sure you need to clean it off and then repressurize the system while under the car. 

  • Like 1
4 hours ago, joshuaho96 said:

Transmission or engine mounts need to be replaced if you get bad shift shock

And while that can be true, it is also possible that the clunk comes from the tailshaft centre bearing, from the diff CW&P lash, from CVs or the splines of the driveshafts into the hubs, etc. Also possible to be in the front drive stuff, but you wouldn't expect anything there to cause much noise on a normal takeoff.

  • Like 1
2 hours ago, GTSBoy said:

And while that can be true, it is also possible that the clunk comes from the tailshaft centre bearing, from the diff CW&P lash, from CVs or the splines of the driveshafts into the hubs, etc. Also possible to be in the front drive stuff, but you wouldn't expect anything there to cause much noise on a normal takeoff.

Good point, there’s a whole class of failures I forgot about that can also cause this. 

Thank you. I did read that the clunk noise can have many different causes. I guess the car needs to go in the air to figure that one out. I did go ahead and ordered this product: https://frenchysperformancegarage.com/collections/nissan-skyline-r32gt-r/products/fpg-bnr32-attesa-high-pressure-hose-replacement-with-optional-pressure-sensor-adapter-fpg-116?variant=42829932724402.

Since I am quit sure that the leak is coming from the Attesa hose. Also it might be leaking at the Atessa pump above the read diff, since I do get a bit of oil leaking from the right side area of the rear-diff, also red colored oil.

Is it harmful to drive every now and then with the car with this small leak?

 

24 minutes ago, T.Krol said:

Is it harmful to drive every now and then with the car with this small leak?

Not if it is actually just a small leak. Just watch your level. But, it could also transition into a really big leak at any moment, and that could be destructive.

so, as I mentioned in another thread on this leak recently, just back off the attessa line where it goes into the rear of the transfer case about 1/2 turn (or 12 turns if I can't type), then tighten it up again. Give everything a thorough degrease and see how it goes.

you can monitor the level of that fluid in the reservoir in the boot, just top it up if necessary

Reservoir was almost at max level without ign on. Topped it off but did a lil too much. I am 8-10mm above max level. Tried to put the ign on and see what it did but it stayed at that level. Is that allright to run the car with a little over max? Havnt turned the car on yet to check the level. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...