Jump to content
SAU Community

Recommended Posts

Hi. My car starts to vibrate the steering wheel when i turn the wheels (it happens more often when iam turning to the right)
But if i stop and try to "park" the car steering wheel shakes in both directions.
it ONLY happens when i try to steer. When iam going straight or slightly turning it is ok.

Could this be bad power steering pump or the whole rack? 
I saw some topic about "death" wobble...it does not do that. Car is not shaking when it drives straight(or slightly turning) or if it sitting idle doing nothing.

Thanks 🙂

Has all the obvious stuff been done, wheel nuts are tight, you've put the car on jack stands and given the wheels a good shake and inspected all the suspension components to ensure everything is nice and tight? 

@The Bogan Yes...it was done tuesday. Before it happens like one time in a month maybe and goes away in a second.
We have done the fluid service and after that it starts doing it. Maybe the new "thicker/better" fluid is too much for the "dying" pump?

@Murray_Calavera Yeah we checked that like month ago...i have new coilovers and bushings...wheels are tight and it does drive "bad" or vibrates from driving...only when i steer the steering wheels starts to shake.
Maybe bubbles in the system? Could this causing this?

And if need to replace the pump...are these pumps same on the "all" R34? Or maybe some other car has the same? (i have RB20DE NEO Manual)
I looked at the parts numbers and genuine pump is like 1050 USD O_O

Edited by Kapr

Don't change the pump, unless they have been run dirty or dry (you will see visible damage/scratches inside if so), you just need to rebuild it with new bearings and seals. I've done the one on my r32 twice now, it is pretty straightforward.

The fluid should just be regular auto trans fluid. If you open the reservoir you should not see any bubbles in the fluid

  • Thanks 1
1 hour ago, Kapr said:

@The Bogan Yes...it was done tuesday. Before it happens like one time in a month maybe and goes away in a second.
We have done the fluid service and after that it starts doing it. Maybe the new "thicker/better" fluid is too much for the "dying" pump?

@Murray_Calavera Yeah we checked that like month ago...i have new coilovers and bushings...wheels are tight and it does drive "bad" or vibrates from driving...only when i steer the steering wheels starts to shake.
Maybe bubbles in the system? Could this causing this?

And if need to replace the pump...are these pumps same on the "all" R34? Or maybe some other car has the same? (i have RB20DE NEO Manual)
I looked at the parts numbers and genuine pump is like 1050 USD O_O

Maybe is hasn't bleed properly 

To bleed mine (different car all together), I jack up the front so the wheels are off the ground, start the car and go full lock left to right a few times

This will force any air trapped in the system out

After flushing mine the power steering pump is all sorts of weird until I do the above bleeding 

If bleeding it doesn't work then maybe look at the pump as Duncan said 

Hopefully it is a simple fix

  • Thanks 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
Ă—
Ă—
  • Create New...