Jump to content
SAU Community

Diff Rebuild or get a mech?

fane

By fane,
in Western Australia

 Share

Recommended Posts

strydes Collaborator

strydes

Posted
Posted

Sorry to hijack this thread, but if you do decide to go for a mech diff, or anyone else out there has an acceptable condition stock diff they would like to get rid of I would be very interested.

As a bit of a background, my diff has a very unpleasant whine which has been diagnosed as a crown wheel and pinion which needs replacing. Will be $250 to fit which is fair enough but Nissan have requested an arm in advance and a leg on pickup to supply me with these parts new.

Therefore, if anyone has access to these parts or has an entire stock diff they would like to sell please PM me as i would be very interested.

Duncan Grand Master

Duncan

Posted
Posted
someone said mech diff wont work with ABS... is it true?

Also anyone heard of Kazaa diff (local)? They cclaim to be quiet and u can retain ur stock diff casing just swap d internals

My mechanical worked fine with ABS. You might have a problem if you change the whole diff casing with one from a car without ABS as the sensor for 3 channel ABS is at the diff.

The amount of clunking you get is controlled by how tight the diff is, a mechanical diff *only* locks under power so if you stay off the accelerator it doesnt clunk, that can make it easier to live with day to day.

And finally you can and should just swap the diff centre, much easier.

rs73 Grand Master

rs73

Posted
Posted

Dunca, is there a certain type of diff that is easier to live off on daily basis,

e.g. 2 way versus 1.5 way versus 1 way? Or is it just a matter of staying on/off accelerator no matter what diff type above?

Also gts-t vspec, how's that Kazaa diff center going and how long ur mate has it? I wonder how these local products compared to things like cusco. Price i believe is much cheaper and quite tempting.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Intercooler Choice

      By Dose Pipe Sutututu · Posted

      Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
    • GTSBoy
      RB26 swapped gtst

      By GTSBoy · Posted

      So.....wire it up appropriately. You can't use the resister pack with those injectors anyway.
    • r33.antwone
      RB26 swapped gtst

      By r33.antwone · Posted

      that’s the thing i’m on ID1050s and haltech not getting power due to the injector resistor 
    • Toilet Goblin
      Intercooler Choice

      By Toilet Goblin · Posted

      ahh okay cheers, i was thinking of just going for the m073, think m079 would be way too overkill considering they are same size. 
    • GTSBoy
      HK Premier with plans for slight mods, but keeping clean and simple

      By GTSBoy · Posted

      My first car was a HG. I'm very familiar with them. A mild cam upgrade is a good idea. The 186 is a very flexible engine - meaning it has good torque from down low. You can give up a little torque down low for quite a lot more excitement in the mid range, and a bit more up top - but they are not exactly a rev monster. You need to upgrade valve springs at the minimum. For a bigger cam, you'd want to make sure it wasn't still running the original fibre cam gear. That would be unlikely, given that most of them shat themselves in the 70s and 80s, but still within the realms of possibility. Metal cam gear required. Carbies are a huge issue. The classic upgrade was always a Holley 350, which works, but is usually pretty bad for fuel consumption. The 186S had a 2 barrel Stromberg on it that was very similar to the one on the 253, and is a reasonable thing if you can find one, and find someone to help you get it set up (which is the same issue with setting up a 350 to work nice). The more classic upgrade was twin sidedraught CD type carbs, or triples of same, or triple Webers. The XU-1 triple Webers being the best example. You can still buy all this stuff new, I think, but it's a lot of coin to drop. And then the people able to set them up are getting fewer and further in between. There's still some, but it used to be everyone's** dad and uncle could do it. **Not everyone's! But a lot. All in all, I wouldn't get too carried away with the engine. Anything you do to it without a full rebuild for power and revs will only make it slightly faster. I am all in favour of a complete teardown rebuild, with nice rods and pistons, 10 or 10.5:1 compression, and a clean port job with at least a big enough cam to run 98 with that compression, if not bigger. And if I did that to a dirty old red motor, I'd want to inject it too, which I'd struggle to fight against the devil on my shoulder that would argue for ITBs and trumpets. But the bills would start to mount up, and it will still never make stupid power. OK, a few people still know how to build absolutely mental red motors, courtesy of the work that went into HQ racing and modern knowledge being applied. But even a 300HP red motor is no match for an RB20 with a TD06. So you have to decide what it's worth to you. I'd just put a set of 6>2>1 extractors, a 2.5" exhaust and an electronic ignition conversion/dizzy on it and just run the old girl like the fairly slow old girl that she really is.
×
×
  • Create New...