Jump to content
SAU Community

Recommended Posts

still no prices? how can you all commit to a group buy if you dont know the price, it could vary quite a few hundered dollars. I'm not participating in this group buy now. I have sourced some Apexi injectors direct from japan for the right price.

-rb25

dude i gave shift a call yesterday and they said they were still waiting on a reply from their suppliers.

It is taking its time but eventually will get there.Sooner rather than later.

:D

I'd be in, but depends on price and when available.....im lookin round for some direct fit injectors for my 33, round the 500-550cc mark. but wouldnt be looking to buy for another 2 months or so.....

my injectors are just maxing out, so there a must have....eventually ;)

Hi Craig,

This is what we have so far I’m, assuming that the injectors are for RB25 ?

The prices are on the basis that at least 9 sets are ordered ok.

HKS 555cc Injectors – Side Feed High Impedance $228 each

NISMO 555cc Injectors $225 each

SARD 550cc Side Feed High Impedance $209 each (includes injectors collars, valued at $42 each)

Cheers

Shift Performance Parts

We dont even have near that many people interested in the group purchase.So do you all wanna back out now because that price is a bit too high for my likings.And by the way i did specify what motor they were for he must have just forgot.Im sending him another email with proper sizes this time so he wont forget.

Cheers everyone.Sorry if the prices are a little out of your leauge.

Yes they said that the whole problem was that they are looking for some new suppliers to buy from in japan and abroad as they will get much better prices then what they have been able to offer us.meh...Sorry ghuys i couldnt do any better on this one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...