Jump to content
SAU Community

Recommended Posts

Here is information about the Type 0 and Type 1 and difference between the two.

TYPE-O has the following functions.

TIMER MODE-This mode keeps engine still running at idle speed after turning the key to off position, and cools down the engine and the turbo by circulating engine oil. This timer has manual, memory and auto mode. Manual mode enables you to set the after-idling time as you like in the range from 0 to 10 minutes (every 30 seconds). Memory mode is the one that several after-idling time is already set in the factory, and you can choose from one of those after-idling times. In the auto mode, turbo timer sets the after-idling length automatically by calculating it from engine running condition.

BATTERY MODE-This is the mode to show the battery voltage in its monitor. If you want, you can set battery warning, which warns you by warning sound and changing the monitor colour when the battery voltage becomes more than 16V or less than 10V.

TYPE-1 has the following functions in addition to two functions which TYPE-O has.

SPEED MODE-This mode shows you driving speed (in the range from 0 to 399 km/h) and also you can set the speed that warning sound will inform you if you drive over that speed.

ENGINE REV MODE- This mode shows you engine rpm and peak rpm. By setting warning function, you can also use this mode for gear-shift timing or red zone indicator.

STOP WATCH AND LAP TIME MODE-

In this mode, you can use this turbo timer as stop watch.

0-400 TIME MODE

In this mode, you can measure the time of 0-400m by using count-down start or auto start that sensed by car speed.

Link to comment
https://www.sau.com.au/forums/topic/499-hks-turbo-timer/#findComment-12830
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...