Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

Mad Wagon. Did you get your RSM sorted out? Do you find that it gets in the way where it is? I have bought one to go on my car when I get it. Can you let me know what the problem was when you find out please? Oh and by the way what size are your rims? I have some 18X9 rear and 18X8 front ones I got in from Ozzy Tyres. The guy said they would fit. I'm starting to think they may not.

Link to comment
https://www.sau.com.au/forums/topic/50201-photos/page/3/#findComment-1021771
Share on other sites

Mad Wagon. Did you get your RSM sorted out? Do you find that it gets in the way where it is? I have bought one to go on my car when I get it. Can you let me know what the problem was when you find out please? Oh and by the way what size are your rims? I have some 18X9 rear and 18X8 front ones I got in from Ozzy Tyres. The guy said they would fit. I'm starting to think they may not.

__________________

hey burkey22,

just fitted r33gtr(17'-9 +30offset) rims today.... they do sorta fit.. but stick out a little bit.

best fittment for stagea rs-four 17" or 18"-8 +30offset ( tested n proven )

Link to comment
https://www.sau.com.au/forums/topic/50201-photos/page/3/#findComment-1022594
Share on other sites

  • 2 weeks later...

I was talking to a mate of mine in Japan because we're looking for TE37s and he came back with this:

> I called the parts shop to specify the parts about Rays Volk TE37 Size is

> 17x8.5 30/40

> They told me this alloy has 2 types. they are 30/40

> If that Stagea is customized as low-down, the wheel size suppose to be

> 17x8.5 30/. However the alloy may scratch the fender of the car.

> If that Stagea is not customized, the wheel size suppose to be 17x8.5 40/

> However it may scratch the inner of the car

>

> The Parts shop adviced me that Ray Volk TE37 has other types.

> They are 17x8J 33/38 33 is for low down and 38 is for normal car.

Link to comment
https://www.sau.com.au/forums/topic/50201-photos/page/3/#findComment-1036711
Share on other sites

One point of advice I was given when i got mine was just like the GTR u should keep the same rubber front and rear or they scrub out coz of the 4wd.  GTR offset seems to be +40.

Keeping the same diameter front and rear is correct, but width is irrelevant. :)

Link to comment
https://www.sau.com.au/forums/topic/50201-photos/page/3/#findComment-1036868
Share on other sites

Thanks for the tip, so same size would be better for rotational purposes only and not so much scrubbing out problem, cheers.

Scrubbing out? That's more of a term I would apply to poor wheel alignment, not different size tyres on a 4wd. Having different diameter tyres on a Stagea will not scrub out tyres, but it will accelerate wear on the ATTESSA 4wd clutches.

Basically what you are looking for is the same rolling diameter of tyres, so;

245/40/17

205/55/16

225/50/16

225/45/17

245/45/16

all have basically the same rolling diameter ~630 mm

An example, if you have say 7.5 X 17 on the front, then 225/45/17 would be OK with 8.5 X 17 on the rear with 245/40/17.

You need to check with your tyre supplier, as diameters vary between brands.

Hope that helps :(

Link to comment
https://www.sau.com.au/forums/topic/50201-photos/page/3/#findComment-1038006
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...