Jump to content
SAU Community

Recommended Posts

  • Replies 87
  • Created
  • Last Reply

Top Posters In This Topic

yeah was an awesome cruise. ive never driven that road before, i had a blast

Moanie - There was a liberty that came unstuck and went into a ditch. Apparently he had pretty stiff suspension and just couldnt get any hold on a bumpy section. he was ok though.

That was me next to you on the way back to the freeway ronin man your mr2 sticks to the road like shit to a blanket :P

Cant wait for next one guys!!

the guy I went up the inside of on the first left hander?

hehe yeh it's not bad :( it's amazing what the right tyres will do for grip :D

yeah was an awesome cruise. ive never driven that road before, i had a blast

Moanie - There was a liberty that came unstuck and went into a ditch. Apparently he had pretty stiff suspension and just couldnt get any hold on a bumpy section. he was ok though.

ohh... ouch!!!! poor guy! :P was the car still driveable afterwards?

I think you guys are missing the "big picture" about the Liberty. If it was modified so as to be undriveable on public roads then you can't really have any sympathy.

May sound harsh but how would you feel about the guy if he bounced off the road into your family?

If the mods had nothing to do with him running off the road the ignore the above. :)

I saw it driving. It looked like it had no suspension at all. It was bouncing all over the joint. He also nearly cleaned up another forum member earlier in the cruise. I'm surprised that hasn't come out yet.

Anyway, we all know Skylines are the kings :D.

hey wats going on seen your post and found it interesting i live on the central coast bout 20 min away from gosford ive heard of people doing that run and of also some racing going on around peats ridge i hear alot of cars come from sydney and do some runs out at peats ridge have you heard any thing about this could you please let me know thanks heaps




  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...