Jump to content
SAU Community

Recommended Posts

Hey Dude,

I have a CA18DET in my Onevia. There is no real downfall for the engines apart form the age. They have a cast iron block.

The stadard turbo is alittle small but with a few simple upgrades the engine is good.

I've reco'd mine with forged pistons and have things like FMIC, GT28, 3" and other basic stuff, I'm about to upgrade AFM and injectors and am expecting 200 rwkw. They are a good engine and react well to boost!

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1030760
Share on other sites

I had a ca18 det in a silvia and can't say anything bad about them - in fact I reckon it was faster than my r33 after a few basic mods. Light cars shouldn't be overlooked!

My old R33 was a beast compared to the 180. Have to say that the CA18DET isn't driving to bad at the moment though.

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1037466
Share on other sites

Sydneykid had a post going on a while ago about some of the upgrades you can give a CA18DET; they're a tough engine, having an iron block (like RB's).

With a strong crankshaft (~$1800), and probably some nicer valve springs, you could easily wind the rev-limit up a bit more. Or get a stroker crank, and make it a CA'20'DET. Now we'd be torquing.

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1043557
Share on other sites

my old strawberry face 180 had a CA18DET that put out 174-178rwkw... its basically the same as an RB20DET engine with 2 less pistons :D very responsive in the lower end. Don't get stupid on the engine trying to poke power out of it (if you need a drift pig you don't really need that much power as you do response, which the CA18DET has when tuned properly) and you should be fine.

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1043564
Share on other sites

  • 2 weeks later...

ca18 is a tuff bit of gear and the only bad thing against this motor is that its a little older now. short stroke desighn (CA18) is a good thing to have in a drift car if you like bouncing your car off the rev limiter as aposed to a SR20 which doesnt like the revs so much but also doesnt need to either.

its a catch 22 but id go the lil CA anyday its a baby 26 in my eyes!

ME:inlove:GTR

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1064968
Share on other sites

The CA18DET has got a downfall!

When revved high for extended periods the pressure builds and forces the oil to build up in the head and cannot run down into the sump quick enough! This can be blocked off like in a stock rb26 since the RB25 can have to same issue.. when this happens look out number 4 cylinder!

fixes can be to bore out the return lines from the head, and block one of the supplies!

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1066461
Share on other sites

i was wondering if anyone has removed the butterfly from the second inlet valve for each cylinder?

removing that and the shaft that holds them..and bit of a port job... would increase the flow dramatically!!!

oh and could you add a second injector into that valve to run 8 injectors, piggy backed off the same cylinder? seems strange separating them like that!

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1068227
Share on other sites

  • 3 weeks later...

I have a 1990 Nissan 200sx (uk) with CA18DET they are good little engine but they have massive problems with big end failure no so much the mains.

Turbo is there second biggest problem little T25 don't last long, cheap upgrade to a S14 T28 normaly does the trick.

Rubbish standard WMIC

(just sold my 48k mile CA and bought a RB20DET (32k miles) much better ) :P

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1095434
Share on other sites

  • 2 weeks later...

I have a CA with only a few bolt on mods and it beats stock SR 20s. I have had it for over a year and havnt had any troubles at all.

Does anyone know where I can get a Apexi Power FC for my CA 18det. Im in Tassie and just wondering if they come pre tuned for the engine? R they hard to install does anyone know. Thanx

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1105995
Share on other sites

Apexi Power FC's are easy to install and come with a basic tune.. but for best performance you would need to get them tuned!

you can get em online or from a performance shop.. autobahn have some but ridiculously overpriced..

checkout greenline or Nengun!

Link to comment
https://www.sau.com.au/forums/topic/51852-ca18det-180sx/#findComment-1106002
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...