Jump to content
SAU Community

Recommended Posts

Putting a switch in line with the 4wd works sure, but you actually have to turn the car off to re-engage 4wd.Has anyone developed a method where you can toggle between 4wd and 2wd without turning the car off.

Why you ask. At the moment at the strip I'd have to start the car with the switch in 2wd drive in , do a burnout, reverse back, turn the car off, put the switch in 4wd, and start the car again for a 4wd run.

Link to comment
https://www.sau.com.au/forums/topic/52365-putting-gtr-into-2wd-and-back/
Share on other sites

Hi ricknismo

Can I ask, why do you have to do a burnout? You may think I'm a big wimp for suggesting this, but with the right tires on your gtr you should get very little/if any wheel spin. (I always drive around the water, and so do some other gtr racers).

Paul and I have played around with the 2 wheel drive alot, but have always had the same issue of having to turn the car off again to get it back into 4 wheel drive. Like doughboy says there is obviously some kit you can install to make this happen. But I prefere to save the rubber.

I have a 33 gtr and just got a 32 gtr...when racing the 33 I often had to wait up to 2 hrs for the next race. The traction compound they put down seemed to make me spin more with cold tyres, I was thinking a skid might heat em up.

HKS Electronic Torque Controller - get it through Nengun or Greenline. An additional module is the EDA - Electronic Drag Adapter which allows constant 4WD (your choice of torque split) up to a specified speed, then it reverts to 2WD (for less drag/resistance).

HKS have discontined the R33 model, but you can still get the R32 + EDA. There are a few other brands like Field but I have had no experience with them.

i don the same as steve, flip the switch fro rear wheel drive, then all you have to do while your reversing is flip it back and stop for a second, 4wd will kick in automatically. thats what i do eeverytime no need to turn the car off

i totally took out the switch and just using the fuse, if i take it out to make the 4wd light come on..it will not go out again when i put the fuse back in and drive.

I have to actually turn the motor off and start it again.

my r32 i would just drive along

turn the engine of for a second and turn it back on... this is like flicking the switch and because you restart the car while it is moving the 4wd tuns off

so no just keep rolling and light up the rears

then when i came to a stop again the 4wd would kick back in

gold

  • 3 months later...

under the bonnet, left hand side, there is a little black box which hopefully should have some boxes and writting on it.

Open it up, its the 3rd one back on the right side which by looking at the lid should be Alternator at the front, Main next and 4wd third.

Yank that sucker out and you'll save $50 on a dyno run and cut a mean skid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...