Jump to content
SAU Community

Recommended Posts

hmm well i've lost two in the past two weeks, mabye the problem runs alittle deeper? i'm running r31 early eccs coilpacks and igniter with an r32 ecu, do you think the later model ecu could kill coilpacks? the igniter and coilpacks look identical to the 32 variaty apart from different electrical plugs on them. they stop working when they get hot only, so they dont entirely die (give it an hour and it comes back).

Whats the condition of the spring inside the coil?

Apparently these can crisp up a little causing problems.

Maybe thats what the problem is?

The spring gets hot looses its tension and doesn't make a proper contact.

GTR's are much better, as there igniter module provides much stronger spark. ND4SPD was running stock coils and module when it made 500rwkw, so it's more than doable. Pity they didn't make the GTS-t's/GTT's as good:(

Are you sure the ignitor is actually different on the GTR..? I think you will find they are the same.

mine shat themselves after 75000km went to split fires, compared them on a bench test to a known good RB coil and the difference was HUGE. The gap jumped by the spark was maxed out to 35mm, on the bench tester, and RPm wound up to 5000rpm and the thing was still sparking a big thick spark. Std RB coil couldn't hack it past 30mm and the spark was noticably thinner and weaker.

Not to mention no more break downs under boost :P

hmm well it seems i've got only .2v at the igniter on the cylinder thats not firing (no 4). i take it the igniter is on the earth side and acts as a big resistor to tame the voltage going through the ecu? so i'd guess its the contacts inside the coil getting too worn. sound feasible?

I've only had one coil die, #2 on my SeriesII R33 and i've been making over 300rwhp for a while now...fingers crossed the others don't follow suit...i've already sussed out splitfires if they do though :uh-huh:

how can u test which coils may be breaking down?

If it's breaking down at idle. Just take a plug of each coil until it makes no difference.

E.G, it will be running on 5 cylinders. When you pull the wrong plug it will run on 4, pull the faulty one, it will run on 5 still.

It wont blow up. The problem with the testing is that they very often don't work only intermittantly (spelling :(), also the consult will not see a problem even when it is actually happening.

I think you need to assume that they all need replacing or fixing because if one or two are stuffed now then another one or two might go soon just when you thought you had fixed it.

I'd imagine coils are a little like engine water hoses.

Once one goes the others follow soon after.

I had one develop a pin hole at the back of the head a few weeks ago. Since then 2 others have gone. All the little b*stards that are hard to get at.

If mine ever go i'll spend the extra $$ and get the good ones.

Well thats the way I have always done it.. on all my Skylines, and it's normally 1 or 2 that go, and you can normally find it on idle and pinpoint it.

I have never had to replace the whole lot on any Skylines in the past 5 Years or so.. :cheers:

I would like a nice set of spitfire coils.. but I can see better things to spend the money on.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
×
×
  • Create New...