Jump to content
SAU Community

Lack of OPTIMAX and unleaded at Shell servo's

wilch

By wilch,
in New South Wales

 Share

Recommended Posts

wilch Grand Master

wilch

Posted
  • Author
Posted

Ok, so I'm bored at work.

I called up their customer service line 1300 134 555 option 3 then 1. Basically they couldn't tell me much.

Optimax apparently comes from only one refinery. The newport refinery. I tried to bait them into saying that there were either issues at the refinery, or issues with delivery. They didn't take the bait.

Ah well, that was fun. It relieved the boredom of work for a few minutes. :D

wil..

Sl!m Grand Master

Sl!m

Posted
Posted

every where I have been today has been good, castlhill,baulkham hills, west ryde.. they all got around $1.12-$1.00..havent filled up for a while.. my car seemed gratefull afterwards lol :D

  • 2 weeks later...
ed Grand Master

ed

Posted
Posted

This is the reply I got from Shell Australia today via email

Dear Edward,  

Thank you for contacting Shell Australia.  

In relation to your enquiry, the shortage of fuels recently has been caused by an unscheduled maintenance  shutdown at our Newport tank terminal. This has caused severe shortages of all  fuels.

The plant is now back on stream, however we anticipate it will take a few more days for  our drivers to  complete the back log of deliveries to  sites.  

It may be that some sites run out of product before the tankers can get back to them.  

We apologise sincerely for the inconvenience this has caused. Please be assured our plant managers and drivers are working around the clock to ensure  consistency of supply as best they are able.

I trust this has been of assistance to you.  

Regards  

Patricia O'Reilly  

Tell Shell Australia  

PH: 1300 134 555  

Guest

Guest

Posted
Posted

Well their is two places (in the World) were they cant sell Optimax and I found out WA is one of them, we only use Ultimate from BP over here, when I lived in Newcastle we always used Mobil's Premium as it is 98.8 to 98.9 (I drove tankers for 6 years and ran a fuel storage area so I learnt a bit about fuel).

One of the Japanese motorcycle builders told buyiers not to use Optimax in one of their up market bikes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...