Jump to content
SAU Community

Hole in the GTT firewall?

FLYGTR

By FLYGTR,
in Victoria

 Share

Recommended Posts

FLYGTR Contributor

FLYGTR

Posted
Posted

Hey guys , just keeping this in the vic part because im sure theres an easy answer . Fitting 2 defi guages ( with controller) on the weekend and just want to know where you can feed the wiring through the firewall? , i had a quik squizz but nothing jumped out at me so i thought id post up to make it easier . Also with the defi's , one is an oil pressure guage so it has a fitting/sender to screw into the oil pump , im guessing the original sender is located their and just want to know if the fitting supplied will screw into the existing sender or an adapter is required.

thanks adam

Link to comment
https://www.sau.com.au/forums/topic/53428-hole-in-the-gtt-firewall/
Share on other sites
Husky33 Veteran

Husky33

Posted
Posted

well if it's anything like an r33(or sils.180's etc) there are a couple hoels. One is a big rubber grommet that sits just above the air con pipes, above the dump pipe area. It's for a loom and it comes out right above the passenger foot rest..shouldn't be too ahrd to spot

NismoR34 Grand Master

NismoR34

Posted
Posted

I have routed all of my wirings through the drivers side - just "above right" of the accelerator - its not easy to run wires through but is the best for what I needed:

A. Direct route to battery - for amp wire

B. Direct route to vacuum hose - for boost gauge

C. Direct route for security stuff

D. Easiest route for A/F Ratio gauge

The wires end up coming out near the original manufacturers plate in the engine bay, green / blue one.

No gromets at either end but you may need to create the initial hole at the drivers / footwell end!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...