Jump to content
SAU Community

Recommended Posts

Would spraying too much water onto your intercooler make it heat up the charge air?

I have 2 sprayers on the cooler which sprays water controller by a 6psi hobs switch...

Its a front mount cooler avo stage 2

Any ideas?

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Can not understand how it could be possible but someone else may want to confirm this.

From a physics perspective, unless the water is substantially hotter than the cooler it will always cool more due to the evaporative effect.

Yes unless you are heating the water by running the water lines 2 close to the engine or exhaust manifold the water will cool the intercooler not heat it up!!

How have you got ur system setup? Are you using the rear window wiper motor for the ic spray?

Guilt - toy, I just posted a message expressing interest in getting a water spray for my cooler - I would definitely think it would have a cooling effect, especially in hotter weather. Evaporating water combined with wind can substantially reduce the temp of an object. Try it on your skin with saliva (Assume the saliva is the same temp as your body). Lick your hand and blow on it. Does it feel cool or hot?

Would spraying too much water onto your intercooler make it heat up the charge air?

I have 2 sprayers on the cooler which sprays water controller by a 6psi hobs switch...

Its a front mount cooler avo stage 2  

Any ideas?

You want the mist to be as fine as possible. On my subaru, I had a water spray set up that used very fine nozzles. The way it was set up, a very fine mist was sprayed in the the bonnet scope in front of the intercooler. The water would vapourise as soon as it touched the coooler or even before, therefore cooling the air.

I have seen a few people do tests on the track. Someone found that garden nozzles which used about 1L/min actually cooled the intercooler much less than misting nozzles which used one twentieth of the water.

When I set mine up, I used three brassnozzles designed for evaporative cooling which I imported from the US. The nozzles are made specifically for cooling sports stadiums and the like.

If anyone is interested, I still have the whole kit inlcuding nozzles, adjustable hobbs pressure switch, relays, switch and a custom made electronic controller which holds the pump on for 5 seconds after boost drops (keeps the pump going between gears). I'm willing to sell this kit as I no longer need it.

Hi Mik,

you had your kit installed on your wrx correct? And with the stocko top mount cooler? How would this kit go on a car with a FMIC?

Do you have pics of the setup?

Cheers,

Scott

You want the mist to be as fine as possible. On my subaru, I had a water spray set up that used very fine nozzles. The way it was set up, a very fine mist was sprayed in the the bonnet scope in front of the intercooler. The water would vapourise as soon as it touched the coooler or even before, therefore cooling the air.

I have seen a few people do tests on the track. Someone found that garden nozzles which used about 1L/min actually cooled the intercooler much less than misting nozzles which used one twentieth of the water.

When I set mine up, I used three brassnozzles designed for evaporative cooling which I imported from the US. The nozzles are made specifically for cooling sports stadiums and the like.

If anyone is interested, I still have the whole kit inlcuding nozzles, adjustable hobbs pressure switch, relays, switch and a custom made electronic controller which holds the pump on for 5 seconds after boost drops (keeps the pump going between gears). I'm willing to sell this kit as I no longer need it.

Hi Mik,

you had your kit installed on your wrx correct?  And with the stocko top mount cooler?  How would this kit go on a car with a FMIC?

Do you have pics of the setup?

Cheers,

Scott

I had it with the stock TMIC.

It will work fine with a front mount, just need to suitably place the nozzles. The nozzles create a large amount of mist. From memory, ach is designed to cool an are of 10 squae meters or something in a sports stadium.

I have attatched a couple of pics of the nozzles.

Included is:

* 3 brass/stainless steel nozzles

* Power switch

* manual override switch

* Adjustable Hobbs pressure swicth

* Electronic control Box

* Power relay to drive pump

* Some hose

All you might need is a little hose if there is not enough there.

IMHO cooler sprays are a waste of time on a street car. In short bursts coolers work more like heat sinks than heat exchangers. That is, they absorb heat on boost and return this heat back to charge air off boost without actually radiating it to air. There isn't enough time to heat the cooler right through unless going hard for long periods. This is different to a track/race car which is on boost most of the time, which has good cause for a spray.

Also most of the effectiveness of the spray is from evaporation (hence the fine mist), so they are rendered useless in high humidity eg. BrisVegas. In BrisVegas a home ducted evaporative air conditioner would be better described as a fan.

IMHO cooler sprays are a waste of time on a street car. In short bursts coolers work more like heat sinks than heat exchangers. That is, they absorb heat on boost and return this heat back to charge air off boost without actually radiating it to air. There isn't enough time to heat the cooler right through unless going hard for long periods. This is different to a track/race car which is on boost most of the time, which has good cause for a spray.

Also most of the effectiveness of the spray is from evaporation (hence the fine mist), so they are rendered useless in high humidity eg. BrisVegas.  In BrisVegas a home ducted evaporative air conditioner would be better described as a fan.

wouldn't it minimise heat soak when you are sitting @ the lights?

This is a simple way of doing it.

http://www.skylinesaustralia.com/forums/sh...ead.php?t=52508

Cheers Rob

The nozzles used there won't do much for cooling, but will waste water.

The water needs to be made into a VERY fine mist to promote evaporation, as that is what causes the cooling effect.

I still dont think the guys question has been answered. He is asking is TOO MUCH water bad.

And out of interest how bad would it be to put say metho or something similar in the water mix? As this would bring temps down even lower correct?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...