Jump to content
SAU Community

Recommended Posts

Hi

Since joining the forums i've learnt a huge amount of information about cars & engines but need some extra information to which i havent found answers for.

I've read about people using difference headgaskets 2.0mm, 1.6, 1.2. When talking about these they refer to Compression Ratio.

I'd just like to know what is compression ratio & why do the headgaskets affect it, all i know about headgaskets is they sit at the top of the engine block just above the end of the pistons i assume. Do different pistons affect CR too?

Anyone who would like to help your info would be much appreciated.

Cheers, :D

PS: Since getting so into skylines i've fell in love with them & engines really interest me now, I'm thinkin i might study to get into it one day, but for the moment i dont want to leave my IT job since its easy good money, plus i enjoy it. Working at a performacne shop building up engines sounds pretty good tho.

Link to comment
https://www.sau.com.au/forums/topic/54202-headgaskets-why-they-affect-cr/
Share on other sites

Compresson ratio is related to the combustion space in the whole cylinder when the piston is at the bottom of its travel compared to when it is at its highest point, so when the piston is at the top of its stroke it sits inline with the top of the block.

there is the headgasket between the block and head, which raises the head and therefore increases the space of the combustion chamber. (compared to if there was not head gasket)

So if you use a thinner than standard headgasket you have decreased the amount of space in the combustion chamber, which will increase the compression ratio, because the piston is going up in the same space but being compressed into a smaller compression chamber.

Therefore increasing the compression ratio... if you know what i mean :D

Not only that it will mess around with the engines "Squish".. so may have negative effects..

Go on then... the effects :D

bringing down the CR sounds good as in a tighter more powerful bang?

Start to get technical on me... owww the difference in 1.2mm & 2mm doesnt sound like much too!

I'm no expert on squish, so won't go into it to much. Best to go and read up on it, do a search.

It's basically the shape made by the crown of the piston and the compression chamber in the head. This effects the way the flame front happens.. which can directly effect how likely your engine is to detonate and how effective the "explosion" is :D

Sometimes you may find that by just adding a thicker gasket to lower compression, you actually get worse detonation even though this is what you were trying to combat.

To do it properly head work must be done.. as I find quite a few GTR's with a larger chamber.. although i'm still not sure about how it's done..

From what I know about Cr and Head Gaskets, Thinner the gasket, eg 1.2 mm will give you better response and drivability, but not able to run as much boost and compared to a gasket that is 1.8mm thick, where you would be able to run more boost but response won't be quiet as good.

But the advantage of a larger gasket is it will keep the cylinders cooler then what a thin one would, reducing detonation. But rembering the only reason most people go an after market head gasket is if your doing a piston replacement, changing the bore size using Forged Oversized pistons to, eg 87mm, 88mm which a standard gasket won't fit. so thats how you get most of your benifits, out of an aftermarket gasket is increasing your cylinder capacity.

Other wise its not worth it.

no not correct..

when the thicker the headgasket, the larger the combustion chamber is so the lower the compression ratio is..

the larger the bore is (say if it is 87.5 instead of 87) the higher the compression would be with the same thickness gasket, as there is more volume in the bore but the combustion chamber is the same.

From what I know about Cr and Head Gaskets, Thinner the gasket, eg 1.2 mm will give you better response and drivability, but not able to run as much boost and compared to a gasket that is 1.8mm thick, where you would be able to run more boost but response won't be quiet as good.  

But the advantage of a larger gasket is it will keep the cylinders cooler then what a thin one would, reducing detonation. But rembering the only reason most people go an after market head gasket is if your doing a piston replacement, changing the bore size using Forged Oversized pistons to, eg 87mm, 88mm which a standard gasket won't fit. so thats how you get most of your benifits, out of an aftermarket gasket is increasing your cylinder capacity.  

Other wise its not worth it.

You can still use a standard head gasket if you have an oversize bore, that is not the reason people use metal gaskets.

usually rb head gaskets are not the source of problems so most people with oversize bore/pretty modified motors use the standard gasket.

By lowering compression I assume you mean raising compression ratio??
In discussions such as this, "compression" and "compression ratio" are the same thing.

The hole in the head gasket effectively becomes an extension of the combustion chamber. So, the thicker the head gasket, the larger the combustion chamber volume. And since

C/R = (cylinder volume + combustion chamber ) / combustion chamber

then a larger combustion chamber (for a given cylinder volume) LOWERS the C/R.

The reason for running the thick head gaskets is to reduce the C/R where a high boost level is being run. This brings into play the difference between "static C/R" and "Dynamic C/R". "Static C/R" is what you measure with a compression meter. It is basically the measure described above. "Dynamic C/R" is a result of ramming additional air (compressed by the turbo) into the cylinder.

Hope I haven't got too technical for you.

Ok thats good info. So if you were wanting to make some large hp out of your rb25det, say 500 bhp+ you might want to do pistons & headgaskets just to make it easier on the engine, you could then cope for much larger power like 550 bhp with cams & a dirty big turbocharger right?

You can still use a standard head gasket if you have an oversize bore, that is not the reason people use metal gaskets.

usually rb head gaskets are not the source of problems so most people with oversize bore/pretty modified motors use the standard gasket.

The standrad nissan Gasket is only good for up to 87mm bore though. Any bigger, you need an aftermarket gasket.

Can't altering the cam timing have effects on your dynamic compression ratio? Thus is you wanted a lower compression you could take the short cut and alter your timing (more overlap) rather than change a head gasket?

Another point maybe is that people think running such a high boost level is what makes power, but boost is just pressure, not cfm. Cfm is what makes the power and torque and should not be confused with boost. Concentrate on moving large volumes of air at a lower boost level whilst still retaining a decent (higher) compression ratio so you dont loose to much down below. I guess at the end of the day what we really want is a nice linear power curve. But if your a drag racer i guess low end doesnt matter.

Sorry if this is hard to understand and please correct me if im wrong

Ok thats good info.  So if you were wanting to make some large hp out of your rb25det, say 500 bhp+ you might want to do pistons & headgaskets just to make it easier on the engine,  you could then cope for much larger power like 550 bhp with cams & a dirty big turbocharger right?

Pistons are a recommended upgrade as the cylinder pressures and temperatures at higher power levels are beyond what the standard cast pistons can handle, they melt/crack/call it quits as soon as the going gets tough.

Headgaskets are normally changed to reduce compression without changing pistons, also since the headgasket resides in the combustion chambers it's one of the first parts in line to cop the increased pressures from higher outputs and detonation. The aftermarket multi-layer metal gaskets are pretty strong, best thing is you can resuse them after cleaning.. provided they aren't damaged.

Static compression is a basic mathematical equation of swept volume + combustion size / combustion size. Dynamic compression takes into account camshafts bleeding out pressure due to overlap + increased duration. Also note that in the higher RPMs when there is less physical time for the valvetrain events to happen combustion chamber filling is greater with the larger camshafts, and so you're going to get higher combustion pressures than smaller camshafts. You really need to take into account head flow stats, as well as manifolds (in + exh) as well as turbine backpressure to accurately calculate cylinder filling, otherwise just suck it and see.

There are a whole bunch of different things you can do to alter the power delivery. The Nissan Group A GT-Rs used to run about a 9.2 C/R and 1.8 bar boost, and delivered something in the order of 450hp. The Sierras probably delivered the same level of power, but did it by running C/R of 6, and 3bar boost (which explains why they were such dogs off-boost, and diabolical in the wet when the power suddenly cut in).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...