Jump to content
SAU Community

Recommended Posts

Get the cams changed, to the suited ones for a R33 CAS.

 

Time wasting and a pain in the A$$ but its the only other option if the FC doesnt work with the R34 cas.

 

Have you done a sensor check on your FC ?

Hi cameron, How do you do a sensor check on the Power FC? What we did do is connect up the R34 CAS to the loom and with the ignition on, spun the spindle and nothing. We did the same with my original CAS and the fuel pump started whirring. So we think maybe something might be wrong with the CAS and it is faulty cause it gets no signal.

Thanks cameron

Ian

I thought all the non-neo RB25 had half circle drive?

well they do from what I can see.. inside the actual "drive" (which is actually a star shape) is a half crescent that hooks up to the cam in the correct position, which I assume is the "key".. i think maybe that is where the confusion is?

For the time you will end up wasting on mucking around with, cams, cas, computers. to trying and get it to work. It would be quicker if you pulled out the cams, contact your supplier and get them to send you the correct cams ASAP and then you send back the R34 ones when they arrive.

For the sake of pulling off the timing belt and water pump, its really not that much hassle, compared to messing around with the wrong CAS, which could give you the wrong IGN reading, which could potentially damage your motor.

That is if your certian they are the wrong cams first.

The cams will work fine in the motor,

The R34 crank angle will work fine as well you just need to rewire it probably needs a pullup resistor inbetween your 2 signals . Grab a multimeter and test your voltage signals and rewire accordingly.. I will call you with regards to this anyway Bullant Im home tomorrow and can do it for you. no point in changing the cams took you long enough to get them from Japan.

Br,

JH

Well if they are the wrong cams, hes going to have to unistall them and send them back and get the correct ones.

You can't run a car with the wrong cams.

The R32 and early R33 models run the 8-point star drive and the half moon that comes out from that locates the CAS in the right position. Like Predator said

Late R33s and R34 cams run what looks like a single strip of metal deep down inside the cam which I think is offset to prevent 180 degree mis-alignment.

Also R32s are hydraulic cams and R34s are mechanical.

I know early R33s are hydraulic cams but I would not be surprised if the late R33s are mechanical cams. Unsure.

But I'm guessing you're getting no zap zap at all out fo your motor

hey ian

its richo..... dude sounds like u are having probs with ur car now i feel the same wat but this has been happening to me with my car for the last 4 months still not on the road

P.S does anyone know where the fuel pump relay is located in a r32 or where bouts in the loom its located im having problems with my GTR pump triggering the pump worked when tested in tank but hit the key and nothing any help would be appreciated

Sorry "E" no one replied to my thread that i posted so i jumped on your horse cheers give us a call

thanks

czy18e

not even ian is a good mate of mine everyone help him out wer live a good 3 hours from any real in person advice so this is really all we got

as for the thread whore ive only been a member for a bout three days

cheers

I would not be surprised if the late R33s are mechanical cams.

I have never seen an R33 GTST RB25DET (non Neo) with solid followers, they have all been hydraulic. The only solid follower equiped RB25DET's I have seen have been the R34 GTT Neo versions.:D

Well thanks all for the advise, the R34 NEO cam is on its way back to the land of the rising sun. The correct cam is on its way to the land downunder which will allow us to use the R33 CAS and hopefully will be be installed on Tuesday.

Thanks again for all the expert advise and we can all learn from this experience.

Ian

Well thanks all for the advise, the R34 NEO cam  is on its way back to the land of the rising sun. The correct cam is on its way to the land downunder which will allow us to use the R33 CAS and hopefully will be be installed on Tuesday.

Thanks again for all the expert advise and we can all learn from this experience.

Ian

Good to see you worked it out,

The moral of the story, All ways check your cams before installing, cause its a b!tch when you have to pull it all out again and put the correct ones back in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...