Jump to content
SAU Community

Recommended Posts

Anyone welcome to a fun day test and tune at benaraby off gladstone on 23rd november.So far:

*My 4 door--hoping for a really low 13 or even a 12

*3040 turboed series 2 gtst --hoping 11's

*T51 180sx ---hoping 12's

*Previously n/a silvia and 32 gts

*32 gtr

*32 gts-squizz's old beast--now doing 14.1's with an open diff

*180sx drift weapon

*bluebird sr20--doing 13's

*black huge turboed 33gtst

*silver series 2 gtst 33--13.6

*black series 1 33 gtst

*hopefully Ben and maybe a few more from streetmachines with their 11 second GTR's

and probably more and thats just from Rockhampton/Yeppoon, the local Gladstone boys will come too.Whack your car on the list if your coming.

I think it costs about $40 and scrutineering happens til about 1 and drags til 5ish.

Link to comment
https://www.sau.com.au/forums/topic/5467-drags-at-benaraby/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

RESULTS:

*My 4 door--13.39

*3040 turboed series 2 gtst--didnt come

*T518Z 180sx ---squizz 13.45

*Previously n/a silvia and 32 gts --not ready in time

*180sx drift weapon--13.7

*bluebird sr20--doing 13's

*black huge turboed 33gtst--kabooom bye bye pistons

*maroon gtst with t3/t4 hybrid--13.36

Link to comment
https://www.sau.com.au/forums/topic/5467-drags-at-benaraby/#findComment-96711
Share on other sites

Originally posted by ricknismo

*T51 180sx ---hoping 12's

SR20 with HKS T51 KAI will probably spool up at about 5000rpm, and should run 10s

CA18 with HKS T51 KAI will probably spool up at about 5500rpm, and should run 10s

Perhaps you mean TRUST T517z or TRUST T518z?

Link to comment
https://www.sau.com.au/forums/topic/5467-drags-at-benaraby/#findComment-97143
Share on other sites

yay for the skylines.....except mine:(

once again keeping those ankle biting little 4's at bay.

The fact that the skylines cost twice as much and were faster by .1 of a second means nothing.....heh heh.

That mph is awesome squizz, can't wait for next time, maybe some decent rubber would go down well.

As for me 300hp at the wheels and a stock computer just didn't go together ....too lean. Time to fit the t78 but not before the microtech and maybe a 3L bottom end.

Link to comment
https://www.sau.com.au/forums/topic/5467-drags-at-benaraby/#findComment-97604
Share on other sites

i think ill have to run hondy next time and show you all how to run 20's!!! go the N/A fwd dorift slug

Bad luck with the skyline garthos but i guess it was never gonna last like that.....:uh-huh:

And to Gti-r boy bagging squizz about 13.4's if ur car really has 164kws at all four why can't you crack a 12 when even a standard Gti-R can huh? You never had your Car and u never had Squizz. Rematch time this thursday..........:shake:

Link to comment
https://www.sau.com.au/forums/topic/5467-drags-at-benaraby/#findComment-97723
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...