Jump to content
SAU Community

Recommended Posts

1. Anyone recommend a better tyre than the Re55s for the same type. Like the Yoko A032s. Dont care about wear. Have used RE540s on the back which are due for replacement.

2. What are peoples opinions on having the REs on the front ie do they tram line a lot, or dangerous in the wet for steering. I know these tyres are no good for the wet and I dont use my car in the wet.

3. Is it advantages to have the same tyres all round? I currently have a missmatch of REs rear and normal front. Thinking of REs all round. By normal I mean a good quality non semi slick. Currently T1s.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/
Share on other sites

1. No, they are the best semi slicks I have used. Possibly Dunlop DZ02G may be as good. Yoko A032R are a second or two worse, except perhaps in the wet.

2. Yep like buggery, all the time, in my experience all semi slicks do, maybe its to do with the stiff sidewall. I don't beleive they are dangerous as such in the wet but you have to be aware that their tread can very quickly wear to a point where they have no wet grip. When they have tread they are not so bad.

3. Possibly, I personally would look for the best grip I can get all round. If by normal you mean street tyres, yes absolutely. At the limit a skyline understeers its front end grip you need :D

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1072203
Share on other sites

  • 2 weeks later...

I've am currently using the RE 55s for my rear 18" 265/35 and Pirelli P7000 for the front 18" 235/40.... not a problem at all... it lasted me for 3months.... i drive my car everyday and everywhere, didnt have any problem, good for cornering with the stiff sidewalls....... i will definitely buy the RE 55s again.....

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1085514
Share on other sites

my 2c...

The car was designed with a 'matching' tyres front to rear in mind. In matching i mean either 4 road tyres (or similar tread / limits) or 4 semi slicks. I don't understand why you would upset the balance of the front to rear grip by putting a set of semis on the front or rear, and roadies at the opposite end.

wilzlee you even mentioned it yourself - semis have much stiffer sidewalls than road tyres, so that alone can affect the way the car handles, and feels at the limit.

OK so if you say you need more rear traction and put semis on the back, I think the problem is not the tyres but the way you drive. Learn throttle control. You don't see race teams running a wet in the front and a dry in the rear (for example, forgetting about compounds) to promote better front grip - it is a geometry or suspension problem.

A car with sorted suspension and matching tread / compound tyres front to rear will be much more enjoyable to drive than a mis-matched combo.

grepin i'm running 225/50/16 RE55s all round, and they're pretty good. As long as you respect them in the wet, they'll be ok and not try and kill you. I found the worst part of them in the wet is hard braking... they will lock up and slide alot faster than a roadie.

They don't tramline too badly, but i'm running 225s... if you go wider they are alot worse. In terms of front to rear, different tread patterns - like i said above, the best to worst scenario is:

1. front and rear same semis

2. front and rear different tread semis of same compound

3. front and rear same roadies

4. front and rear different tread roadies of similar tread / compound

5. mis-matched front to rear semis / roadies

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1086001
Share on other sites

My opinions as I use the RE55's.

1. I've never used them myself but I believe the Dunlop DZ02G's are supposed to be as good - but cost nearly twice the price. The Advans definitely aren't as grippy.

2. The tramline EVERYTHING. Drives me crackers at times! LOL. I've never had any issues with them in the wet.

3. I recently ran with the RE55's on the fronts and some Advan A048's on the rear - thinking oversteer at Sandown would be better than understeer. Was a pain in the ass with the different compounds as the car just wasnt balanced. Would have been better with both front and back on the Advans than trying to put the better compund just on one end.

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1086710
Share on other sites

The impression i had before was getting a pair of RE55s for the rear mainly because when a rwd takes on a faster corner, the tail tends to slide out, and i thought that the semis can help a lil more by keeping the tail 'IN'. note taken ronin... =) i shall purchase all 4 semis next.... keep it balanced......

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1090844
Share on other sites

The impression i had before was getting a pair of RE55s for the rear mainly because when a rwd takes on a faster corner, the tail tends to slide out, and i thought that the semis can help a lil more by keeping the tail 'IN'. note taken ronin... =) i shall purchase all 4 semis next.... keep it balanced......

sorry mate, I got a bit excited there... but yeah, set up the suspension, bars etc. and you'll love it even more :)

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1090900
Share on other sites

well, personally I think skylines run out of front grip first when driven hard, like most cars these days...if you are get oversteer or wheelsping thru the corners maybe some throttle control practice would be cheaper than good tyres.

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1091556
Share on other sites

I was sitting here nodding my head to that Duncan but then I thought; Ok the easy answer is a poofteenth less throttle and your oversteer will go away, but, that's basically saying drive around the track slower and you wont have grip problems.

It seems to me that you want your car to be neutral in regards to under/oversteer.

Wilzlee - Isn't the whole 'rwd's oversteer in fast corners' a bit of an outdated stereotype? Steering and suspension in modern cars has come a long way since that was necessarily the case.

My car has stock suspension still and I have always had the same tyres front and back. It is completely neutral as Duncan can attest to as he has seen me 4 wheel drift the last turn at wakefield before the straight.

Just my 2c.

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1092261
Share on other sites

Ahhh well if we want to be technical about it, a car *never* oversteers from going to fast unless there is actually less grip at the rear.

So excluding what you do with your foot in a RWD car, or weight shifting by braking or lifting off, or some weird setup where you have worse or narrower tyres at the rear....the front end will slide first.

Makes sense when you think about it, if grip levels are equal the front gets there first and slides first.

If you are getting oversteer before understeer you:

1) Have a poor suspension setup or

2) Crap back tyres

3) Poor technique...braking *too hard* into the apex of the corner, backing off throttle suddenly or getting on the throttle suddenly.

Driving more "smoothly" will almost always eliminate oversteer....brake in a straight line (about 80%)....trail brake into the corner smoothly (no sudden change in brake)....accelerate smoothly out of the corner (no sudden change in throttle)

Quite apart from all that, manufacturers all build understeer into suspension these days so ham fisted drivers dont get snap oversteer and kill themselves....natural reaction when loosing control is lift off or brake suddenly, with an oversteer prone setup you then spin...if you keep understeering by design at least you will see what you hit and have the crumple zones and airbags to save you

Link to comment
https://www.sau.com.au/forums/topic/54870-re-55s/#findComment-1092699
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...