Jump to content
SAU Community

Recommended Posts

Anybody know of anywhere good on the goldcoast to get a car complied? Preferably somewhere where somebody has had their car complied in the last 12 months and has some first hand experience.

Mine shall be here in a couple of weeks.. just wondering whether there were any places down here that came recommended at a good price, with as little dodginess as possible.

Might be nice to get it done somewhere locally. Then again I might just get it all done up in Brisbane, then I just can go up there and pick it up.

p.s. my car is in the yellow dot right now :)

Animation06.gif

:D

Link to comment
https://www.sau.com.au/forums/topic/55285-compliance-goldcoast/
Share on other sites

I just heard on the news that there was a Tsunami around the area of the yellow dot Gordo :D

Seriously though PM Jason (JLNewton) as I think he had all three of his cars complied on the Coast

yeah, its 15 year..

I thought about doing the work myself, replacing things like cat, seatbelts, brake light, etc.. then getting engineer to do intrusion bars. I have room here to work on it.

Just got to weigh up cost of somebody else doing it for $1200 or so, or doing it myself, buying the parts, and go from there. I have a feeling the DIY may be up around $700 (any idea exactly how much it will cost me ??).. if I can just take it somewhere and in a week pick it up all done and ready to register, that is very tempting.

Shipping could be around $100 just to get it to the goldcoast though from the docks. Guess that is not too bad if I end up doing much of the compliance myself.

If I get it done up brissie though, I just pick the car up, take it to the nearest transport dept, and straight to the goldcoast.

*dilema*

Yeah, got both my cars complied down the Coast. If you need any details or info drop us a PM Gordon. I found this guy good to deal with, other people have had different experiences though, but personally I found him upfront and easy going.

theres a place at nerang thats will do it i think its around the $500 mark ( don't know where i got that figure from??) post up a contact # tonight for you, but i'm talking to a place tomorrow about a compliance plate for my car, engine swap and the other bits, but i'll ask for a price on the import compliance your looking for tomorrow..

That would be great... at the moment its at Brisbane docks getting looked at by customs. Once that's done (few days more I think) going to get it shipped down via car carrier to my place, where I might do some of the work myself.

Then can just get it taken to a place that can write out the engineers, and then to the transport dept. for rego.

from the place i'm going to talk to tomorrow i was told its $165 for the inspection and mod plate through them but i'll confirm that first. the blokes name is Jason Ruse, automotive techique ph # 07 5537 1515 there in labrador just off brisbane road, round the road from Dyson rotorary...

I dont mean to hijack the thread or anything, but instead of starting another one about compliance centers in brisbane i'm sure if ANYONE in either gold coast or brisbane has had their r32 gtr complianced under 15yo rule, how much did it cost you and what needed to be done?

My GTR is completely stock standard, stock muffler etc. I have a local muffler guy who will swap the cat to a new one virtually for free, but if its the stock cat do you still have to change it?

Predator: good stuff.. I would be very interested in your experience from gettin the car complied to getting it on the road. Mine's at the customs atm too (no its not a line.. :) ) so I will have to go throught the same thing as you soon. :( Diff is that the person that is importing my car will also be arranging compliancing.

Pentae: I believe there is a threat at the "Importation, Laws and Regulations section" on what needs to be done for a R32 GTR's compliancing, it might even be a DIY use the search option man. :)

I would also be interested to see how long your car took going throught the custom, as I have been told its anywhere between 4 days till 3 weeks. :)

  • 8 months later...

Hey matt.. um its the one behind smith street in Southport..

adrenaline i think it was.. they didn't do my actual compliance, but they were friendly about letting the engineer they use tick off my work.. and they looked quite legit, and had decent service.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...