Jump to content
SAU Community

Recommended Posts

I enquired about them - apperantly they only come in a kit so you have to buy all the little metal peices which include the shims, plates etc. I'm can't remember if the pins are included.

I had a diagram with all the peices from FAST but I've had a look and don't have the page with the actual kit on it (i seem to have every other brake diagram).

If you call nissan and ask them for the skyline front caliper kit for all the little metal peices they should be able to give you the part number. Make sure you get them to fax you the page with the part number they're talkin bout circled, I've found sometimes they're talkin bout one thing, ordering another.

I lost 3/4 of my rear shims.. I'm running without them now - seems to work ok :(

Good luck.

I enquired about them - apperantly they only come in a kit so you have to buy all the little metal peices which include the shims, plates etc. I'm can't remember if the pins are included.

I had a diagram with all the peices from FAST but I've had a look and don't have the page with the actual kit on it (i seem to have every other brake diagram).

If you call nissan and ask them for the skyline front caliper kit for all the little metal peices they should be able to give you the part number. Make sure you get them to fax you the page with the part number they're talkin bout circled, I've found sometimes they're talkin bout one thing, ordering another.

I lost 3/4 of my rear shims.. I'm running without them now - seems to work ok :(

Good luck.

Your last thread got derailed I know, but I found my old ones if you want them PM me...

TT

Sorry Busky I don't recall a price - I think it was around $160 though because I do recall thinking "I don't believe they are $80 a set.. i don't believe i lost practically $160 worth of parts."

But then again that could be ENTIRELY wrong and not even in the ballpark - call nissan!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...