Jump to content
SAU Community

Recommended Posts

FS: Volk/Rays TE37 in bronze (5 x 114.3)

F: 18 x 8.5 (+30)

R: 18 x 9.5 (+35)

Wheels are in good condition, but not in the same excellent condition as the Work Meister S1's and the GT2's...

Also come with a full set of Volk/Rays wheel nuts (in black to match the stickers!)

l2ite372.th.jpg

More pics tonight....

Once again, the best price around - happy to send interstate

$2,100

Kind Regards,

Jeff.

Link to comment
https://www.sau.com.au/forums/topic/57807-fs-volkrays-te37/
Share on other sites

Guest two.06l
FS: Volk/Rays TE37 in bronze (5 x 114.3)

F: 18 x 8.5 (+30)

R: 18 x 9.5 (+35)

Wheels are in good condition, but not in the same excellent condition as the Work Meister S1's and the GT2's...

Also come with a full set of Volk/Rays wheel nuts (in black to match the stickers!)

l2ite372.th.jpg

More pics tonight....

Once again, the best price around - happy to send interstate

$2,340

Kind Regards,

Jeff.

Would you consider selling the nuts? if so how much?

Link to comment
https://www.sau.com.au/forums/topic/57807-fs-volkrays-te37/#findComment-1112558
Share on other sites

Seems to be a lot of interest in GTR fitments - wait until February!

Anyway, more pics showing the condition of the wheels...

j7rvolks.th.jpg

l5pte371.th.jpg

The worst example of gutter damage:

i9dte373.th.jpg

Paint damage evident on one wheel. There is no structural damage whatsoever, it appears as though (maybe battery acid, thinners???) has splashed and eaten into the paint. No amount of polishing will remove it! However, the surface is smooth to the touch:

a1ete374.th.jpg

Up close:

w2qte375.th.jpg

Hott interest in these - keep it coming...

Link to comment
https://www.sau.com.au/forums/topic/57807-fs-volkrays-te37/#findComment-1112718
Share on other sites

I have fitted these to an R33 Gtst without issue.

The fronts fit perfectly, plenty of caliper clearance (Brembo’s would fit easily) whilst remaining inside the guards.

The rears are a tighter fit, coming close to the suspension on the inside and sitting just inside the guards – but still fit. Over big bumps and/or extreme lowering (as per your previous cars!) they could hit, I can’t be sure. However, rolling the rear guards would be a necessity, as would stretched rubber.

Now, if an R32 is the same/very similar in this area as an R33, you will be ok. Whether they are the same is another question…

Trial fitting is welcome (however, I know you are in Perth)...

Link to comment
https://www.sau.com.au/forums/topic/57807-fs-volkrays-te37/#findComment-1129616
Share on other sites

  • 2 months later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...