Jump to content
SAU Community

Recommended Posts

Hey guys

Last week I picked up my '95 GTR Vspec.

I'm damn happy with its performance, but I would really like some more bottom end. The car is completely stock. It even has the factory boost restrictor in place.

What can I do to get more bottom end. The car feels like it has no power whatsoever below 3 grand. Now im not too keen on doing too many mods because I am broke. I also dont need any more attention that im getting from cops and the like. So i'd like to keep it as stock as possible (incl stock exhaust).

Opinions and advice please

Thanks

Link to comment
https://www.sau.com.au/forums/topic/59839-stock-gtr-33-feels-slow-what-to-do/
Share on other sites

Make sure the timing is correct.

Change any fuel filters that are old.

Check the plugs and the gaps are correct as well.

Get a compression test done by a mechanic and a dyno.

Just to check where things are at.

If its as bad as you say there may be an underlying fault somewhere.

Plus make sure the factory cat convertor isn't blocked which can cause excess back pressure and loss of torque.

An exhaust will also help bring boost on sooner which will make the bottom end more responsive. (If you have a crappy press bent factory one)

Its just undergone compliance, so all fluids have already been changed, etc etc.

It really isnt that slow, but the take off compared to other gtr's is much slower. Driving around the city at about 2000 revs isnt that much fun. Perhaps I'm being a bit pedantic.

But honestly, there is no pickup from the turbos until about 3-3500 revs. And compared to my old stock gts-t, it's much slower under 4 grand

4 grand up its a monster :P

Would a boost controller help boost pick up any quicker ?

I have one still handy

hi, with a boost controller you will be able to bring the boost on earlier, although not by a large amount.

generally speaking, there is nothing you can do if you are used to the gtst

i have had two gtsts, and am often in a stockish gtr, and i know exactly what you mean about the slowness..

by the time my gtst reaches 4 grand you are accellerating pretty quickly and about to break traction, whereas you really need to keep the revs above 4 grand in the gtr to get a similar response. its normal, just fit the electronic boost controller and get used to it :P

Full exaust/front pipes/hi flow cat first..

then Adjustable Cam gears will help bring boost on alot earlier.

and take out the boost restricter, (won't really help low rpm tho, where the exaust/cam gears will)

very true

well ive been driving it a fair bit for the last week or so.

I'm also slowly getting used to driving it, and becoming more accustomed to its driving style

Revving it out when I need more power, and around the streets up to 3k rpm is sufficient

yeah dont drive it like a wuss!! my last gtr and my current one (both 32s ) seemed a little sluggish below 3500rpm but remember they do rev to 8k! definatly do an exhaust first, 3 inch at least and tuned lengh front pipes with high flow cat, will make more power and more rb26 noise!

have you dropped it from 7k yet??? damn it feels fast when you do that!!

my gtr is stock and I removed the boost restrictor and boost went up from 12psi to 14psi and gave me an extra 22awkw (with standard exhaust) and on the road it blows away a lot of more powerful cars

have you dropped it from 7k yet??? damn it feels fast when you do that!!

my gtr is stock and I removed the boost restrictor and boost went up from 12psi to 14psi and gave me an extra 22awkw (with standard exhaust) and on the road it blows away a lot of more powerful cars

Did removing the boost restrictor give you much better response down low ?

I'm having a fair bit of trouble removing this restrictor. Need to get the right set of pliers :)

Damn, the fuel economy on this thing aint too bad either. Averaging between 11-13 litres/100. Highway/city driving :D

Did removing the boost restrictor give you much better response down low ?

I'm having a fair bit of trouble removing this restrictor. Need to get the right set of pliers :)

 

Damn, the fuel economy on this thing aint too bad either. Averaging between 11-13 litres/100. Highway/city driving :)

Squeeze the restrictor out from the outside, use any sort of pliers and pop it out like a cork, should take you a couple of minutes. probably didnt help much below 3G although definately hit boost harder and pulled better through to redline.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...