Jump to content
SAU Community

dumbass r32 @ maloolaba

gatty

By gatty,
in Queensland

 Share

Recommended Posts

gatty Mentor

gatty

Posted
Posted

hey

Wondering if the owner might read this, wine R32 - number plates XXX GXE (i think), would have been last wednesday night - took off at the lights trying to 'race' this mx5 that iw as following - then a car doing the speed limit (he was doing about 120 ish in 50 zone) was comeing up - over took it on the outside, almost got wiped out by a parked 4WD

just wanted to say i think your a dumb **** - people like you cause my insurance bill to be 3k a year - BTW nice solo race, quite obvious the mx5 wasn't interested

if you do read this i was the guy who followed you into maroochydore in the silver 33 - the one you again tried to 'race' before cutting in front of me because you almost missed your turn

bumbass

Link to comment
https://www.sau.com.au/forums/topic/60180-dumbass-r32-maloolaba/
Share on other sites
SkylineSII Enthusiast

SkylineSII

Posted
Posted

Yeah well dickheads are on the coast as well last night around 11 i was driving back home alone the highway and three old ford xr8's tried to drag me down the highway eventually they got the hint that i wont lose my licence and stoped trying.

Then they had another idea that they would block me in since i was in the far left lane and had a wall on my left side i had no where to go so it took me about 20 mins to get from up near worongary to the ashmore exit. Due to the fact we were doing 20km's down the highway.

The whole time yelling out if u drag us we will let u go and blah blah blah i was more worried about what they would do to my car i mean their car had dents all over it and so on so i just sat there and kept silent.

The Dan Grand Master

The Dan

Posted
Posted

hahaha, I raced a bunch of XR8's the same. They kept trying to block me in and my missus was getting scared so she gave me permission to lose them.

I think the dents you are referring to would be from a tyre iron I threw at him. I thought I'd ad some value to his heap of crap. That is of course if it's the same one. They tried to follow me all the way into brisbane but got pulled up by traffic for speeding coz I knew the cops were there and the wanks didn't...hahahahaha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By GTSBoy · Posted

      I don't think the shuffle can damage the turbos. It only happens at low shaft speeds and loads. It's just annoying (to some people - others are tickled by the effect) and it quite possibly reduces spool performance a little bit.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      Can u check this way it works for power supply?
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      These coils draw 10amps that what i read online
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
×
×
  • Create New...