Jump to content
SAU Community

Recommended Posts

Hi Lads,

Cannot find answer after numerous searches. I live in a hot climate, and as a result the air-con sometimes takes a while to work. I set my unit to 20 degrees and only the foot vents work until the car cools down enough, then the top (dash) vents open. Must switch once the difference between the set value and the AMB value is small enough (maybe 8 or 9 degrees).

What really annoys me though, is that I cannot manually turn the top vents open until the cabin cools enough to automatically switch.

Is this normal? Can I override this?

Thanks, regards

Link to comment
https://www.sau.com.au/forums/topic/60237-r32-gtr-air-con/
Share on other sites

The climate control has a feature that isn't documented in the R32 owner's manual.

With the fan on, temperature set at 18 (the lowest it will go), press and hold the temperature

down button for a couple of seconds. The climate control will show "FC", the air conditioning

will come on in re-circulated mode. This must be a fast cool, as it sets the optimum setting for

cooling the car quickly. The re-circulation mode can be turned off.

There is a "FH" mode also with the temperature set at 32 (the highest temperature). Press and

hold the temperature up button to enter the FH (fast heat?) mode.

Link to comment
https://www.sau.com.au/forums/topic/60237-r32-gtr-air-con/#findComment-1145869
Share on other sites

Lads - thanks for the comments.

I know about the mode button - it switches to manual but still does not change vents.

I know and use the FC mode quite regularly - we must have downloaded the same skyline 'book!'

I ran a diagnostic check a few weeks ago, and it came up with a sunload error (common, ignored) and a water termerature sensor error. I do not think this has anything to do with the vents, though, as the AC is bloody cold when its working.

It just takes a little time to switch vents over, depending on the inside car temp.

Thanks for the comments lads.

Link to comment
https://www.sau.com.au/forums/topic/60237-r32-gtr-air-con/#findComment-1147409
Share on other sites

He had the car for a few days, Changed from old gas to new, cylender was damaged so he had to degas it, replace and regas it again. new control unit, from memory around 300. the guy I use is really really good. I always take any of my cars to him without a worry

Who is this guy? How much for the gas switch?

Cheers,

Lucien.

Link to comment
https://www.sau.com.au/forums/topic/60237-r32-gtr-air-con/#findComment-1147447
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...