Jump to content
SAU Community

Recommended Posts

I was at my local Autobahn on Sunday and noticed that they sell 2 cruise control (1 brand, 2 diff models).

1 runs of sensors on your accellerator pedal and the other connects into your ecu and pulses the speed signal wire.

The 2nd 1 was ~$420 + $160 installation.

I have no idea what brand it was but I read thru the brochure and it seemed fine.

When you're shopping around for them, check out the cruise cancel functions. In your family car it prob cancels on clutch pedal, brake pedal, or cancelling on the unit itself.

Only reason I'm throwing in my 2.2c is because a workmate had an accident in the wet where the car (nothing stupid happened, it was a AU Falcon on the F3) fishtailed after it aquaplaned, and then the transmission shat itself as he was travelling backwards (as in car did 180 turn) and the ECU was still trying to maintain 110kmh. Turns out it was his aftermarket cruise did not have effective cancelling switches installed. Apologies if the story is a bit vague, it happened a while ago.

Mark

I have an auscruise unit fitted to my R32 gtst. Autobarn Elizabeth fitted it. I bought the unit on one of their 20% off days, but all up fitted cost around $550 i think. I had lots of problems getting it to cruise smoothly though. Would hunt for speed (ie accelerate through, then off throttle, deccelerate back through set speed) was real annoying. Car went back about 5 times until they set the unit up right that it cruises nicely. Just reacts slowly, unlike a factory fitted unit. So basically make sure they have the ability to reprogram the control module, to suit the car. I think i had so much problem because of how touchy the throttle is when cruising (ie 110km or so).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...