Jump to content
SAU Community

Recommended Posts

  • Replies 300
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Well guys, I have just removed the Pepsi can gasket from underneath my BOV. While it was blocked off I noticed that boost came on much harder and also faster in between gear changes. I tested this on stock boost with the factory solenoid controlled by the ECU and also with the solenoid grounded running straight 7psi. On both settings there were absolutely no idle/stalling issues. I only drove about 10KM as I do not want to find out how reliable this setup is.

It sounded fulleh sik but also made the car more responsive on boost and also quicker to get there.

Is there anyone else who has run their factory RB25 S2 turbo without a BOV for a lengthy period of time who can report on reliability?

Haha I used Coke :(

Yeah the turbo will be fine, even at 10psi or higher without a BOV there would be no damage. I think people start thinking stuff in there head and panic, when theres nothing to worry about.

Are you gonna keep the fully sick setup?

Yeah i have the stall problem sometimes, do you know what it is caused from?

Ive done about 1000km

:(

Edited by r32matt

Aside from making you a hectic bro - I have found that it has made my car more responsive, keep in mind that it is a genuine low kays S2 33 gts and i am running stock boost with a blitz pod and 3" cat back otherwise standard.

lol!

Im guessing you havent read the last 14 pages :(

Putting some metal or a coke can under the BOV blocks it off from the intercooler pipe. Then you just block off the tube that runs from the manifold to the BOV and you will get Fully Sick Flutter.

If you want details or instructions just PM me :(

Edited by r32matt
Ah if u can fit it in the gap, it won't do a whole lot, the can wil probably get shaken up and will eventually de-carbonate, it won't cool it down either, your best bet is the fridge

haha i didnt understand any of that?? :(:woot::(

Ah if u can fit it in the gap, it won't do a whole lot, the can wil probably get shaken up and will eventually de-carbonate, it won't cool it down either, your best bet is the fridge

haha!! Nice

Nah he doesnt mean a full can :(

Gotta cut the can out to be the shape of the BOV. Put it in like its a seal and it will block up the hole.

The small tube which runs to the top of the BOV - Unplug that from the BOV and block it up (screw or something)

Would you like a diagram? :(

Just curious y did u block the tube off?

Just that i didn't think it would matter, it's only for pressure regulation (i think ) and as it's not getting any pressure i'd think it wouldnt make any difference whether blocked off or not. Correct me if im wrong but air only goes into the manifold nothing goes the other way right? (which i probably am not)

And na u shouldnt need to block the plumbback as it's not getting any air to it either

Edited by 123456

Nah the Plumb Back is fine, ive left all of that still on.

When I left the manifold tube unblocked my car wouldnt boost properly and was holding back, felt really bad!

Im pretty sure the tube is a vacuum which opens the BOV when you take your foot off.

What have u done with your manifold tube? did you leave yours in the BOV? I guess that would work the same if the BOV wasnt opening. Hmm might have to try, but yeah had a few boost problems with that pipe.

Edited by r32matt

Yeh i just left mine on BOV,

Only reason im asking is coz im lazy and if i decide im sick of flutterz i want it to be easy to switch back

"Im pretty sure the tube is a vacuum which opens the BOV when you take your foot off"

Yeh thats what i meant, wasn't thinking of what i was typing lol

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Welcome!  How long have you had it? And what colour is it?
    • "CAD" version 1.0 It will have a 15mm lip around the top for 6 × 5 or 6mm nutserts and fixtures (two on each of the three straight edges), and some pinch weld on any exposed edges, it has three mounting points, one of the power steering reservoir bolts, and two on the rad support, my 120mm hole saw will make short work of hole for the silicone joiner, with ample room for some pinch weld  I've also got enough Carbuilders "peel and stick" heat shield to cover the outside of it at the coolant expansion tank and on the engine side, as pictured, and internally on the lid and where the fuse box is, I've also got some thin, about 3mm, black 3M single sided sticky foam stuff that was left over after sealing some door drafts at home to help seal the lid As for the shape, it "sort of" matches the shape of the fuse box, so shouldn't look to "out of place" The lower area and hole for the intake will need pinch weld with a balloon on it to fully seal the hole and bottom of it, that will happen after it has been fabricated so I know exactly what size is required  Filter service has been trialed,  and so far it was a simple process  Just need to get some alloy, and then head into work to use the guillotine and break press in the workshop Hopefully it should be sorted in a week or two Guestimated outlay will be under a $50 for the stuff I don't have on hand (alloy, 6mm nutserts, the pinch weld, and wrinkle paint) Disclaimer: That's what the "voices in my head" are telling me how the filter box should end up getting done......lets see if they know what they are talking about  
    • Have been polishing up the trailer rims as they had been sitting in the shed for a few years and are really in need of some love. This was after a couple of passes with chrome polish - coming up quite well ✅ .
    • Welcome aboard! Is your Skyline auto or manual? I'm assuming manual. Does it have any mods done yet?
    • Hey mate, the brown and grey plugs would usually go to the TPS, brown one goes on the bottom connector and grey is the top but isn't used unless the car is auto, your TPS looks different to mine though I've got a series 2 engine.
×
×
  • Create New...