Jump to content
SAU Community

Recommended Posts

  • Replies 300
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Well guys, I have just removed the Pepsi can gasket from underneath my BOV. While it was blocked off I noticed that boost came on much harder and also faster in between gear changes. I tested this on stock boost with the factory solenoid controlled by the ECU and also with the solenoid grounded running straight 7psi. On both settings there were absolutely no idle/stalling issues. I only drove about 10KM as I do not want to find out how reliable this setup is.

It sounded fulleh sik but also made the car more responsive on boost and also quicker to get there.

Is there anyone else who has run their factory RB25 S2 turbo without a BOV for a lengthy period of time who can report on reliability?

Haha I used Coke :(

Yeah the turbo will be fine, even at 10psi or higher without a BOV there would be no damage. I think people start thinking stuff in there head and panic, when theres nothing to worry about.

Are you gonna keep the fully sick setup?

Yeah i have the stall problem sometimes, do you know what it is caused from?

Ive done about 1000km

:(

Edited by r32matt

Aside from making you a hectic bro - I have found that it has made my car more responsive, keep in mind that it is a genuine low kays S2 33 gts and i am running stock boost with a blitz pod and 3" cat back otherwise standard.

lol!

Im guessing you havent read the last 14 pages :(

Putting some metal or a coke can under the BOV blocks it off from the intercooler pipe. Then you just block off the tube that runs from the manifold to the BOV and you will get Fully Sick Flutter.

If you want details or instructions just PM me :(

Edited by r32matt
Ah if u can fit it in the gap, it won't do a whole lot, the can wil probably get shaken up and will eventually de-carbonate, it won't cool it down either, your best bet is the fridge

haha i didnt understand any of that?? :(:woot::(

Ah if u can fit it in the gap, it won't do a whole lot, the can wil probably get shaken up and will eventually de-carbonate, it won't cool it down either, your best bet is the fridge

haha!! Nice

Nah he doesnt mean a full can :(

Gotta cut the can out to be the shape of the BOV. Put it in like its a seal and it will block up the hole.

The small tube which runs to the top of the BOV - Unplug that from the BOV and block it up (screw or something)

Would you like a diagram? :(

Just curious y did u block the tube off?

Just that i didn't think it would matter, it's only for pressure regulation (i think ) and as it's not getting any pressure i'd think it wouldnt make any difference whether blocked off or not. Correct me if im wrong but air only goes into the manifold nothing goes the other way right? (which i probably am not)

And na u shouldnt need to block the plumbback as it's not getting any air to it either

Edited by 123456

Nah the Plumb Back is fine, ive left all of that still on.

When I left the manifold tube unblocked my car wouldnt boost properly and was holding back, felt really bad!

Im pretty sure the tube is a vacuum which opens the BOV when you take your foot off.

What have u done with your manifold tube? did you leave yours in the BOV? I guess that would work the same if the BOV wasnt opening. Hmm might have to try, but yeah had a few boost problems with that pipe.

Edited by r32matt

Yeh i just left mine on BOV,

Only reason im asking is coz im lazy and if i decide im sick of flutterz i want it to be easy to switch back

"Im pretty sure the tube is a vacuum which opens the BOV when you take your foot off"

Yeh thats what i meant, wasn't thinking of what i was typing lol

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...