Jump to content
SAU Community

Recommended Posts

  • Replies 101
  • Created
  • Last Reply

Top Posters In This Topic

yeah ive been trying to get it from blocky but its always out

oooo couldnt find the one u had shan but i just ordered this... http://www.lik-sang.com/info.php?category=...roducts_id=202& should be here next week.

ok...

if u wanna runs PS2MAME and run all 2000+games that are available u need a gamlist.txt file... im writing one up now which should allow you to run most of the games.

unless someone has one already... saves me making one

The good people at AusDigital have released an all-in-one GUI based Exploit disc compiler to make life VERY easy for everyone. details at http://www.ausdigital.net/

Enjoy !

P.S. Just tested the compiler, it works 100%. Took about 90 seconds to get a full .ISO image ready to burn, & it installed no probs. Too easy.

heres a list of games that havent worked for me so far that arent on that other list.

-WRC 4

-V8 Supercars 2

-MC3 Dub

all copied from the PS2 to the HDD using original disks.

have sent them through but they havent been updated to the list.

The good people at AusDigital have released an all-in-one GUI based Exploit disc compiler to make life VERY easy for everyone. details at http://www.ausdigital.net/

Enjoy !

P.S. Just tested the compiler, it works 100%. Took about 90 seconds to get a full .ISO image ready to burn, & it installed no probs. Too easy.

omg thats awesome!

so does this mean i dont need a memory card editor to do it?

damn... wish u posted this last week before i ordered one :)

With the PS2 slim, does the USB drive have to be powered? what if I use a notebook HDD?

I have a notebook HDD in a USB box, it powers from the USB port on the PS2. Use a short cable or you may encounter probs (didn't like the USB ext. cable).

Hi, Alex from AusDigital here. If you are unsure where to start, or what to have (You need a method of booting..) Then visit my newbie page here and fill out the form at the bottom.

http://ausdigital.net/?go=start

It should point you in the right direction at least!

cool

yeah i went though all that last night and realised i will have to wait for the memory card editor to come cause i dont have a mod to bott the CD i made... duh on my part

very cool site btw

munkeh - i was just dumping them from the PS2 directly, not through my PC.

oh yeah munkeh i will have to redo everything too (will use the CD created using ausdigitals compiler) cause now when i boot it doesnt load the keylauncher anymore... goes str8 to HDLoader

Hi CK,

SoulCalibur 2 - Only works with ToxicOS HDL/HDA, a hack version.

GT3 - should work OK.

GT4 - needs to be patched & PC installed (HDLdumb, Winhiip etc) a somewhat involved process.

GT3 doesn't work with HDAdvanced 2.1 :(

What's the hack version?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...